会员中心 | English | 繁體中文

梅花槽盘头 AB ABR自攻螺钉 ASME B 18.6.3 (H5C-VI+T1A) - 2024

选择规格尺寸点击↓

10#

12#

1/4

5/16

3/8

7/16

1/2

ASME B 18.6.3 (H5C-VI+T1A) - 2024 梅花槽盘头 AB ABR自攻螺钉

尺寸单位: inch

美标ASME B18.6.3 (H5C-VI+T1A) - 2024 ASME1 梅花槽盘头 AB ABR自攻螺钉

扫一扫分享

公差最小破坏扭矩牌号等级

螺纹尺寸
d

d	公称
PP
d_k	最大值
	最小值
k	最大值
	最小值
R	最小值
槽号
M	参考值
P	最大值
	最小值
L₀ ^④	公称
Y ^④	螺纹过渡长度(全螺纹)	最大值
b ^④	螺纹长度 (长螺钉)	最小值

0.0600	0.0730	0.0860	0.0990	0.1120	0.1250	0.1380	0.1510
48	42	32	28	24	20	20	19
0.116	0.142	0.167	0.193	0.219	0.245	0.270	0.296
0.104	0.130	0.155	0.180	0.205	0.231	0.256	0.281
0.044	0.053	0.062	0.071	0.080	0.089	0.097	0.106
0.036	0.044	0.053	0.062	0.070	0.079	0.087	0.096
0.005	0.005	0.010	0.010	0.010	0.015	0.015	0.015
T5	T6	T8	T8	T10	T10	T15	T15
0.058	0.069	0.094	0.094	0.111	0.111	0.132	0.132
0.020	0.030	0.035	0.038	0.045	0.055	0.055	0.060
0.015	0.025	0.030	0.033	0.035	0.045	0.045	0.050
7/16	9/16	5/8	3/4	13/16	15/16	1	1-1/8
0.021	0.024	0.031	0.036	0.042	0.050	0.050	0.053
0.360	0.440	0.520	0.590	0.670	0.750	0.830	0.910

螺纹尺寸
d

10#

12#

1/4

5/16

3/8

7/16

1/2

d	公称
PP
d_k	最大值
	最小值
k	最大值
	最小值
R	最小值
槽号
M	参考值
P	最大值
	最小值
L₀ ^④	公称
Y ^④	螺纹过渡长度(全螺纹)	最大值
b ^④	螺纹长度 (长螺钉)	最小值

0.1640	0.1900	0.2160	0.2500	0.3125	0.3750	0.4375	0.5000
18	16	14	14	12	12	10	10
0.322	0.373	0.425	0.492	0.615	0.740	0.863	0.987
0.306	0.357	0.407	0.473	0.594	0.716	0.837	0.958
0.115	0.133	0.151	0.175	0.218	0.261	0.305	0.348
0.105	0.122	0.139	0.162	0.203	0.244	0.284	0.325
0.015	0.020	0.025	0.035	0.040	0.040	0.050	0.055
T20	T25	T27	T30	T40	T45	T50	T55
0.155	0.178	0.200	0.221	0.266	0.312	0.352	0.446
0.070	0.085	0.085	0.100	0.120	0.145	0.159	0.180
0.055	0.070	0.070	0.085	0.105	0.130	0.144	0.165
1-1/4	1-3/8	1-5/8	1-13/16	1-13/16	1-7/8	1-7/8	1-7/8
0.056	0.062	0.071	0.071	0.083	0.083	0.100	0.100
0.980	1.140	1.300	1.500	1.500	1.500	1.500	1.500

①,若以小数规定公称直径，应省略小数前和小数点后第四位的零。
②,螺钉末端钉尖上不允许因螺纹辗压而形成的虚尖，允许略带圆弧或圆钝形末端。
③,小于等于8#的螺钉，螺纹牙顶平面宽度不应超过0.004in，大于8#的应不超过0.006in。
④,正常情况下，当螺钉长度小于等于其公称长度L0时应采用全螺纹，过渡螺纹长度应小于等于Y；若螺钉长度大于其公称长度L0可采用半牙型式，但其螺纹长度应不小于b。

替代列表

ASME B 18.6.3T19-VI+T40 - 2013 ASME B 18.6.3H5C-VI+T1A - 2024

引用参考

GB /T 1172 - 1999

黑色金属硬度及强度换算值

GB /T 5267.1 - 2002

镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能

GB /T 193 - 2003

普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)

GB /T 3106 - 2016

紧固件 - 螺栓、螺钉和螺柱 - 公称长度和螺纹长度 (ISO 888:2012, MOD)

GB /T 3 - 1997

普通螺纹收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983)

GB /T 5779.1 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 一般要求

GB /T 5779.3 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 特殊要求

注：技术数据仅供参考，请以官方原件为准！

类似标准及供货信息

1	[国标] GB /T 2670.1 - 2017	内六角花形盘头自攻螺钉 Hexalobular Socket Pan Head Tapping Screws 供应商(2)
2	[国标] GB /T 2670.2 - 2017	内六角花形沉头自攻螺钉 Hexalobular Socket Countersunk Head Tapping Screws 供应商(1)
3	[国标] GB /T 2670.3 - 2017	内六角花形半沉头自攻螺钉 Hexalobular Socket Raised Countersunk(Oval) Head Tapping Screws 供应商(1)
4	[国标] GB /T 2670.1 - 2004	内六角花形盘头自攻螺钉 Hex lobular socket pan head tapping screws 供应商(2)
5	[国标] GB /T 2670.2 - 2004	内六角花形沉头自攻螺钉 Hexalobular Socket Countersunk Head Tapping Screws 供应商(1)
6	[国标] GB /T 2670.3 - 2004	内六角花形半沉头自攻螺钉 Hexalobular Socket Raised Countersunk(Oval) Head Tapping Screws 供应商(1)
7	[德标] DIN 34819 - 2008	梅花槽圆头凸缘（华司）自攻钉 Hexalobular Socket Raised Head Tapping Screws With Collar
8	[国际] ISO 14585 - 2011	梅花槽盘头自攻螺钉 Hexalobular Socket Pan Head Tapping Screws 供应商(3)
9	[国际] ISO 14586 - 2011	梅花槽沉头自攻螺钉 Hexalobular Socket Countersunk Head Tapping Screws 供应商(1)
10	[国际] ISO 14585 - 2001	梅花槽圆头自攻螺钉 Hexalobular Socket Pan Head Tapping Screws 供应商(3)
11	[国际] ISO 14586 - 2001	梅花槽沉头自攻螺钉 Hexalobular Socket Countersunk Head Tapping Screws 供应商(1)
12	[国际] ISO 14587 - 2011	梅花槽半沉头自攻螺钉 Hexalobular Socket Raised Countersunk（Oval） Head Tapping Screws
13	[国际] ISO 14587 - 2001	梅花槽半沉头自攻螺钉 Hexalobular socket raised countersunk（oval） head tapping screws
14	[日标] JIS B 1128 (O) - 2004	梅花槽半沉头自攻螺钉 Hexalobular Socket Raised Countersunk Head Self-Tapping Screws
15	[日标] JIS B 1128 (F) - 2004	梅花槽沉头自攻钉 Hexalobular Socket Countersunk Head Self-Tapping Screws
16	[日标] JIS B 1128 (P) - 2004	梅花槽盘头自攻钉 Hexalobular Socket Pan Head Self-Tapping Screws
17	[汽标代号] Q 27A	内六角花形盘头自攻螺钉 Hex lobular socket pan head tapping screws
18	[汽标代号] Q 27B	内六角花形沉头自攻螺钉 Hexalobular socket countersunk head tapping screws
19	[汽标代号] Q 27C	内六角花形半沉头自攻螺钉 Hex lobular socket raised countersunk head tapping screws
20	[汽标代号] Q 2A2	塑料用内六角花形盘头自攻螺钉 Hexalobular socket pan head tapping screws for plastic
21	[法国] NF E 25-652 - 2001	梅花槽沉头自攻螺钉 Hexalobular Socket Countersunk Head Tapping Screws
22	[法国] NF E 25-653 - 2001	梅花槽半沉头自攻螺钉 Hexalobular Socket Raised Countersunk（Oval） Head Tapping Screws
23	[法国] NF E 25-654 - 2001	梅花槽盘头自攻钉 Hexalobular Socket Pan Head Tapping Screws
24	[企标] YJT 4025 (WN 5451)	塑料用梅花槽圆头带介自攻螺钉【DELTA PT 螺纹】 Round Washer Head with TORX PLUS Self-tapping Screw [DELTA PT Thread] 供应商(1)
25	[企标] YJT 4052	梅花槽水泥钉003 (T30) 供应商(1)
26	[企标] YJT 4059 (WN1423C-1)	梅花槽沉头自攻螺钉 Hexalobular Socket countersunk head Tapping screws 供应商(1)
27	[企标] YJT 4060 (WN1423C-2)	梅花槽沉头自攻螺钉 Hexalobular Socket countersunk head Tapping screws 供应商(1)
28	[企标] YJT 4065 (WN1451C)	梅花槽盘头带垫自攻螺钉 Hexalobular socket Pan Head Tapping Screws With Collar 供应商(1)
29	[企标] YJT 4066 (WN1452C)	梅花槽盘头自攻钉 exalobular Socket Pan Head Self-Tapping Screws 供应商(1)
30	[企标] YJT 4083 (WN5452)	塑料用梅花槽盘头自攻螺钉 [DELTA PT 螺纹] Pan Head with TORX PLUS Self-tapping Screw [DELTA PT Thread] 供应商(1)
31	[企标] YJT 4067 (WN1453C)	梅花槽半沉头自攻螺钉 Hexalobular Socket Raised Countersunk（Oval） Head Tapping Screws
32	[德标] DIN EN ISO 14587 - 2011	内六角花形半沉头自攻螺钉 Hexalobular Socket Raised (Oval) Head Tapping Screws
33	[德标] DIN EN ISO 14585 - 2002	内六角花形盘头自攻螺钉 Hexagon Socket Pan Head Tapping Screws
34	[德标] DIN EN ISO 14586 - 2002	内六角花形沉头自攻螺钉 Hexalobular Socket Countersunk Head Tapping Screws
35	[汽标] QC /T 878 - 2011	塑料用内六角花形盘头自攻螺钉 Hexalobular socket pan head tapping screws for plastic 供应商(1)
36	[美标] ASME B 18.6.3 (H1B-VI+T1A) - 2024	梅花槽82°沉头 AB ABR自攻螺钉 82° Countersunk head with hexalobular slot tapping screws - Type AB (ABR)
37	[美标] ASME B 18.6.3 (H2B-VI+T1A) - 2024	梅花槽半沉头 AB ABR自攻螺钉 Hexalobular socket raised countersunk head tapping screws - Type AB and ABR
38	[美标] ASME B 18.6.3 (H6B-VI+T1A) - 2024	梅花槽球面扁圆柱头 AB ABR自攻螺钉 Cheese Head Tapping Screws with Hexalobular Slot - Type AB and ABR
39	[美标] ASME B 18.6.3 (H7B-VI+T1A) - 2024	梅花槽大扁头 AB ABR自攻螺钉 Mushroom Head Tapping Screws with Hexalobular Slot - Type AB and ABR
40	[美标] ASME B 18.6.3 (H12B-VI+T1A) - 2024	梅花槽圆头凸缘 AB ABR自攻螺钉 Hexalobular Socket Round Head Tapping Screws With Collar - Type AB and ABR
41	[美标] ASME B 18.6.3 (T2-VI+T40) - 2013	梅花槽82°沉头 AB ABR自攻螺钉 82° Countersunk head with hexalobular slot tapping screws - Type AB (ABR)
42	[美标] ASME B 18.6.3 (T8-VI+T40) - 2013	梅花槽半沉头 AB ABR自攻螺钉 Hexalobular socket raised countersunk head tapping screws - Type AB and ABR
43	[美标] ASME B 18.6.3 (T19-VI+T40) - 2013	梅花槽盘头 AB ABR自攻螺钉 Hexalobular Socket Pan Head Tapping Screws - Type AB and ABR
44	[美标] ASME B 18.6.3 (T22-VI+T40) - 2013	梅花槽球面扁圆柱头 AB ABR自攻螺钉 Cheese Head Tapping Screws with Hexalobular Slot - Type AB and ABR
45	[美标] ASME B 18.6.3 (T25-VI+T40) - 2013	梅花槽大扁头 AB ABR自攻螺钉 Mushroom Head Tapping Screws with Hexalobular Slot - Type AB and ABR
46	[美标] ASME B 18.6.3 (T39-VI+T40) - 2013	梅花槽圆头凸缘 AB ABR自攻螺钉 Hexalobular Socket Round Head Tapping Screws With Collar - Type AB and ABR
47	[日本汽车工业协会标准] JASO F 116 - 2005	梅花槽盘头自攻螺钉 T-type TORX pan head tapping screws
48	[日本汽车工业协会标准] JASO F 116 - 2005	梅花槽沉头自攻螺钉 T-type TORX countersunk head tapping screws
49	[日本汽车工业协会标准] JASO F 116 - 2005	梅花槽半沉头自攻螺钉 T-type TORX raised countersunk head tapping screws
50	[日本汽车工业协会标准] JASO F 116 - 2005	梅花槽扁圆头自攻螺钉 T-type TORX truss countersunk head tapping screws
51	[日本汽车工业协会标准] JASO F 116 - 2005	梅花槽盘头带垫自攻螺钉 T-type TORX collar head tapping screws