会员中心 | English | 繁體中文

内六角锥端紧定螺钉 [Table 14] (ASTM F912 / F880) ASME B 18.3 (T14 CONE) - 2012

选择规格尺寸点击↓

10#

1/4

5/16

3/8

7/16

1/2

5/8

3/4

7/8

1-1/8

1-1/4

1-3/8

1-1/2

1-3/4

ASME B 18.3 (T14 CONE) - 2012 内六角锥端紧定螺钉 [Table 14] (ASTM F912 / F880)

尺寸单位: inch

美标ASME B18.3 (T14 CONE) - 2012 ASME18.3 内六角锥端紧定螺钉 [Table 14] (ASTM F912 / F880)

扫一扫分享

单重计算公差美制螺纹极限尺寸米/英制螺纹对照螺纹直径与受力截面积最小破坏扭矩牌号等级

螺纹规格
d

10#

1/4

5/16

3/8

d	螺纹直径
PP	粗牙/UNC
	细牙/UNF
	超细牙/UNEF
s	公称
t	最小值
L	最短公称长度
α	公称

0.0600	0.0730	0.0860	0.0990	0.1120	0.1250	0.1380	0.1640	0.1900	0.2500	0.3125	0.3750
-	64.0	56.0	48.0	40.0	40.0	32.0	32.0	24.0	20.0	18.0	16.0
80.0	72.0	64.0	56.0	48.0	44.0	40.0	36.0	32.0	28.0	24.0	24.0
-	-	-	-	-	-	-	-	-	32.0	32.0	32.0
0.028	0.035	0.035	0.050	0.050	0.062	0.062	0.078	0.094	0.125	0.156	0.188
0.050	0.060	0.060	0.070	0.070	0.080	0.080	0.090	0.100	0.125	0.156	0.188
0.13	0.19	0.19	0.19	0.19	0.19	0.25	0.25	0.25	0.31	0.44	0.44
90°	90°	90°	90°	90°	90°	90°	90°	90°	90°	90°	90°

螺纹规格
d

7/16

1/2

5/8

3/4

7/8

1-1/8

1-1/4

1-3/8

1-1/2

1-3/4

d	螺纹直径
PP	粗牙/UNC
	细牙/UNF
	超细牙/UNEF
s	公称
t	最小值
L	最短公称长度
α	公称

0.4375	0.5000	0.6250	0.7500	0.8750	1.0000	1.1250	1.2500	1.3750	1.5000	1.7500	2.0000
14.0	13.0	11.0	10.0	9.0	8.0	7.0	7.0	6.0	6.0	5.0	4.5
20.0	20.0	18.0	16.0	14.0	12.0	12.0	12.0	12.0	12.0	-	-
28.0	28.0	24.0	20.0	20.0	20.0	18.0	18.0	18.0	18.0	-	-
0.219	0.250	0.312	0.375	0.500	0.562	0.562	0.625	0.625	0.750	1.000	1.000
0.219	0.250	0.312	0.375	0.500	0.562	0.562	0.625	0.625	0.750	1.000	1.000
0.63	0.63	0.88	1.00	1.00	1.25	1.50	1.50	1.75	2.00	2.25	2.50
90°	90°	90°	90°	90°	90°	90°	90°	90°	90°	90°	90°

替代列表

ASME B 18.3 - 2003(R2008) ASME B 18.3 - 2012

工艺相关

ASME B 18.3 (Table 18) - 2012

内六角凹槽对边尺寸偏差 [Table 18]

引用参考

GB /T 1172 - 1999

黑色金属硬度及强度换算值

GB /T 5267.1 - 2002

镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能

GB /T 193 - 2003

普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)

GB /T 3106 - 2016

紧固件 - 螺栓、螺钉和螺柱 - 公称长度和螺纹长度 (ISO 888:2012, MOD)

GB /T 3 - 1997

普通螺纹收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983)

GB /T 5779.1 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 一般要求

GB /T 5779.3 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 特殊要求

注：技术数据仅供参考，请以官方原件为准！

类似标准及供货信息

1	[国标] GB /T 78 - 2007	内六角锥端紧定螺钉 Hexagon Socket Set Screws with Cone Point 供应商(3)
2	[国标] GB /T 78 - 2000	内六角锥端紧定螺钉 Hexagon Socket Set Screws with Cone Point 供应商(3)
3	[国标] GB 78 - 1985	内六角锥端紧定螺钉 Hexagon Socket Set Screws with Cone Point 供应商(3)
4	[德标] DIN 914 - 1980	内六角锥端紧定螺钉 Hexagon Socket Set Screws With Cone Point 供应商(3)
5	[国际] ISO 4027 - 2003	内六角锥端紧定螺钉 Hexagon Socket Set Screws With Cone Point 供应商(1)
6	[国际] ISO 4027 - 1993	内六角锥端紧定螺钉 Hexagon socket set screws with cone point 供应商(1)
7	[日标] JIS B 1177 (T3) - 2007	内六角锥端紧定螺钉 Hexagon Socket Set Screws With Cone Point
8	[日标] JIS B 1177 (T2) - 1997	内六角锥端紧定螺钉 Hexagon socket set screws with cone point
9	[日标] JIS B 1177 - 1988	内六角截锥端螺钉 Hexagon socket screws with cone point
10	[汽标代号] Q 288B	内六角锥端紧定螺钉 Hexagon socket set screws with cone point
11	[美标] ASME/ANSI B 18.3 - 2003	内键槽锥端紧定螺钉 Spline socket set screws (cone point)
12	[美标] ASME/ANSI B 18.3.6M (CONE) - 1986 (R2002)	米制内六角锥端紧定螺钉 (ASTM F912M / F880M /A1-70) Hexagon Socket Set Screws with Cone Point - Metric (ASTM F912M / F880M /A1-70)
13	[意大利] UNI 5927	内六角锥端紧定螺钉 Hexagon Socket Set Screws With Cone Point
14	[法国] NF E 25-172 - 2004	内六角锥端紧定螺钉 Hexagon Socket Set Screws With Cone Point
15	[英标] BS 2470 - 1973	BA螺纹内六角锥端紧定螺钉 Table 6C Hexagon Socket Set Screws With Cone Point - BA Thread
16	[英标] BS 2470 - 1973	统一螺纹内六角锥端紧定螺钉 Table 6A Hexagon Socket Set Screws With Cone Point - Unified Thread
17	[英标] BS 2470 - 1973	英制内六角锥端紧定螺钉 Table 6B Hexagon Socket Set Screws With Cone Point - BSW and BSF Threads
18	[澳标] AS /NZS 1421 - 1996	米制内六角锥端紧定螺钉 [Table 3] ISO Metric Hexagon Socket Set Screws - Cone Point [Table 3]
19	[台湾] CNS 4481 - 1981	内六角锥端紧定螺钉 Hexagon socket set screws with cone point
20	[韩标] KS B 1028 (T2) - 1990 (R2020)	内六角锥端紧定螺钉 Hexagon Socket Set Screw with Cone Point
21	[德标] DIN EN ISO 4027 - 2004	内六角锥端紧定螺钉 Hexagon Socket Set Screws With Cone Point 供应商(3)
22	[美标] ASME B 18.3 - 2003 (R2008)	内六角锥端紧定螺钉 [Table 5A] Hexagon Socket Set Screws (Cone Point)