会员中心 | English | 繁體中文

开槽沉头自攻螺钉 ISO 1482 - 2011

选择规格尺寸点击↓

ST2.2

ST2.9

ST3.5

ST4.2

ST4.8

ST5.5

ST6.3

ST8

ST9.5

尺寸单位: mm

国际ISO 1482 - 2011 ISO1482 1482ISO 开槽沉头自攻螺钉

扫一扫分享

单重计算公差

螺纹规格

ST2.2

ST2.9

ST3.5

ST4.2

ST4.8

ST5.5

ST6.3

ST8

ST9.5

P	螺距
a	最大值
d_k	最大值
	最小值
k	最大值
n	最大值
	最小值
r	最大值
t	最大值
	最小值
y	参考值	C型
		F型
		R型

0.8	1.1	1.3	1.4	1.6	1.8	1.8	2.1	2.1
0.8	1.1	1.3	1.4	1.6	1.8	1.8	2.1	2.1
3.8	5.5	7.3	8.4	9.3	10.3	11.3	15.8	18.3
3.5	5.2	6.9	8	8.9	9.9	10.9	15.4	17.8
1.1	1.7	2.35	2.6	2.8	3	3.15	4.65	5.25
0.7	1	1.2	1.51	1.51	1.91	1.91	2.31	2.81
0.56	0.86	1.06	1.26	1.26	1.66	1.66	2.06	2.56
0.8	1.2	1.4	1.6	2.0	2.2	2.4	3.2	4.0
0.6	0.85	1.2	1.3	1.4	1.5	1.6	2.3	2.6
0.4	0.6	0.9	1	1.1	1.1	1.2	1.8	2
2.0	2.6	3.2	3.7	4.3	5.0	6.0	7.5	8.0
1.6	2.1	2.5	2.8	3.2	3.6	3.6	4.2	4.2
/	/	2.7	3.2	3.6	4.3	5.0	6.3	/

替代列表

ISO 1482 - 1983 ISO 1482 - 2011

等效标准

国标 GB	国际 ISO	德标 DIN
GB /T 5283	ISO 1482	DIN EN ISO 1482

以上有部分标准可能为近似等效，如有异议以标准原件为准

工艺相关

ISO 225

紧固件螺栓、螺钉、螺柱和螺母尺寸代号和标注

耐腐蚀不锈钢紧固件的机械性能Part4:自攻螺钉

ISO 4042

紧固件一电镀涂层系统

ISO 4759-1

紧固件公差 Part1:螺栓、螺钉、螺柱和螺母产品等级 A、B和 C级

技术条件和引用标准

材料
通用要求
螺纹	公差
机械性能	等级
	标准
公差	产品等级
	标准
表面处理
验收及包装

钢（ISO 2702）	不锈钢
ISO 8992
ISO 1478
/	A2-20H，A4-20H，A5-20H
ISO 2702	ISO 3506-4
A
ISO 4759-1
不经处理电镀 ISO 4042 非电解锌片涂层 ISO 10683 其他表面处理由供需双方协议	不经处理钝化 ISO 16048
ISO 3269

引用参考

镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能

GB /T 193 - 2003

普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)

GB /T 5280 - 2002

自攻螺钉用螺纹

注：技术数据仅供参考，请以官方原件为准！

类似标准及供货信息

1	[国标] GB /T 5283 - 2017	开槽沉头自攻螺钉 Slotted Countersunk（Flat）Head Tapping Screws
2	[国标] GB /T 5283 - 1985	开槽沉头自攻螺钉 Slotted Countersunk Head Tapping Screws
3	[美标] IFI 502 - 1982	米制开槽沉头自攻钉 Metric Slotted Countersunk Head Tapping Screws
4	[德标] DIN 7972 - 1990	开槽沉头自攻钉 Slotted countersunkhead tapping screws 供应商(2)
5	[国际] ISO 1482 - 1983	开槽沉头自攻螺钉 Slotted countersunk head tapping screws
6	[日标] JIS B 1115 (JA4) - 2015	开槽沉头自攻钉 [表JA4] Slotted Countersunk head tapping screws [Table JA3]
7	[日标] JIS B 1115 (T6) - 2015	开槽沉头自攻钉 [Table 6] Slotted Countersunk Head Tapping Screws [Table 6]
8	[日标] JIS B 1115 (T2) - 1996	开槽沉头自攻钉 [表2] Slotted countersunk head tapping screws [Table 2]
9	[日标] JIS B 1115 (AT2) - 1996	开槽沉头自攻钉 [附表2] Slotted Countersunk head tapping screws [Annex Table 2]
10	[美标] ASME/ANSI B 18.6.3 - 2010	80°开槽沉头自攻钉 80° Machine Screw and Tapping Screw Nuts (Inch Seires)
11	[法国] NF E 25-660 - 1994	开槽沉头自攻螺钉 Slotted Countersunk Head Tapping Screws
12	[英标] BS 4174 - 1972	开槽80°沉头自攻钉 [Table 8] Slotted 80°countersunk Head Self-Tapping Screws [Table 8]
13	[英标] BS 4174 - 1972	开槽80°沉头清根自攻钉 [Table 10] Slotted 80° Truncated Countersunk Head Screws [Table 10]
14	[澳标] AS /NZS 4404 - 1996	米制开槽沉头自攻螺钉 ISO metric slotted countersunk head tapping screws
15	[台湾] CNS 4303 - 2000	开槽沉头自攻螺钉 Slotted Countersunk Head Tapping Screws
16	[德标] DIN EN ISO 1482 - 2011	开槽沉头自攻钉 Slotted Countersunkhead Tapping Screws 供应商(2)
17	[美标] ASME B 18.6.3 (H1A+T1A) - 2024	82°开槽沉头自攻螺钉 AB(ABR)型 82° Slotted Flat Coutersunk Head Tapping Screws - Type AB (ABR)
18	[美标] ASME B 18.6.3 (H3A+T1A) - 2024	开槽82°沉头清根自攻螺钉 82° Slotted Undercut 82-deg Flat Countersunk Head Tapping Screws
19	[美标] ASME B 18.6.3 (T1+T40) - 2013	82°开槽沉头自攻螺钉 AB(ABR)型 [Table 1+Table 40] 82° Slotted Flat Coutersunk Head Tapping Screws - Type AB (ABR) [Table 1+Table 40]
20	[美标] ASME B 18.6.3 (T9+T40) - 2013	开槽82°沉头清根自攻螺钉 [Table 9+Table40] 82° Slotted Undercut 82-deg Flat Countersunk Head Tapping Screws [Table 9]
21	[美标] ASME B 18.6.5M (T8) - 2000 (R2010)	米制开槽沉头自攻螺钉 [Table 8] Metric slotted countersunk head tapping screws [Table 8]
22	[美标] ASME B 18.6.4 - 1998 (R2005)	A型开槽沉头自攻螺钉 [Table 9] Slotted Flat Countersunk Head Tapping Screws - Type A
23	[美标] ASME B 18.6.4 - 1998 (R2005)	B,BP型开槽沉头自攻螺钉 [Table 9] Slotted Flat Countersunk Head Tapping Screws - Type B and BP
24	[美标] ASME B 18.6.4 - 1998 (R2005)	C型开槽沉头自攻螺钉(统一螺纹) [Table 9] Slotted Flat Countersunk Head Tapping Screws - Type C
25	[美标] ASME B 18.6.4 - 1998 (R2005)	AB型开槽沉头自攻螺钉 [Table 9] Slotted Flat Countersunk Head Tapping Screws - Type AB
26	[美标] ASME B 18.6.4 - 1998 (R2005)	开槽沉头清根自攻螺钉 B,BP型 [Table 13] Slotted Undercut Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 13]
27	[美标] ASME B 18.6.4 - 1998 (R2005)	开槽沉头清根自攻螺钉 C型(统一螺纹) [Table 13] Slotted Undercut Flat Countersunk Head Tapping Screws - Type C Thread Forming [Table 13]
28	[美标] ASME B 18.6.4 - 1998 (R2005)	开槽沉头清根自攻螺钉 AB型 [Table 13] Slotted Undercut Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table 13]
29	[美标] ASME B 18.6.4 - 1998 (R2005)	开槽100°沉头自攻螺钉 B,BP型 [Table VI1] Slotted 100° Flat Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table VI1]
30	[美标] ASME B 18.6.4 - 1998 (R2005)	开槽100°沉头自攻螺钉 AB型 [Table VI1] Slotted 100° Flat Countersunk Head Tapping Screws - Type AB Thread Forming [Table VI1]