会员中心 | English | 繁體中文

不淬硬钢和奥氏体不锈钢内螺纹圆柱销 ISO 8733 - 1997

选择规格尺寸点击↓

Φ6

Φ8

Φ10

Φ12

Φ16

Φ20

Φ25

Φ30

Φ40

Φ50

尺寸单位: mm

国际ISO 8733 - 1997 ISO8733 8733ISO 不淬硬钢和奥氏体不锈钢内螺纹圆柱销

扫一扫分享

单重计算公差公制螺纹极限尺寸米/英制螺纹对照

公称直径
d

Φ6

Φ8

Φ10

Φ12

Φ16

Φ20

Φ25

Φ30

Φ40

Φ50

d	公称 (m6)
	最大值
	最小值
a	≈
c	≈
d₁
P	螺距
d₂
t₁
t₂	最小值
t₃

6	8	10	12	16	20	25	30	40	50
6.012	8.015	10.015	12.018	16.018	20.021	25.021	30.021	40.025	50.025
6.004	8.006	10.006	12.007	16.007	20.008	25.008	30.008	40.009	50.009
0.8	1	1.2	1.6	2	2.5	3	4	5	6.3
1.2	1.6	2	2.5	3	3.5	4	5	6.3	8
M4	M5	M6	M6	M8	M10	M16	M20	M20	M24
0.7	0.8	1	1	1.25	1.5	2	2.5	2.5	3
4.3	5.3	6.4	6.4	8.4	10.5	17	21	21	25
6	8	10	12	16	18	24	30	30	36
10	12	16	20	25	28	35	40	40	50
1	1.2	1.2	1.2	1.5	1.5	2	2	2.5	2.5

替代列表

ISO 8733 - 1986 ISO 8733 - 1997

工艺相关

ISO 965-2

ISO一般用途米制螺纹--公差 part2:内螺纹和外螺纹的极限尺寸

紧固件 - 耐腐蚀不锈钢紧固件的机械性能 Part 1: 螺栓、螺钉和螺柱

技术条件和引用标准

材料 ^①

钢

奥氏体不锈钢

硬度
螺纹
表面处理
表面粗糙度
表面缺陷
验收及包装
备注

硬度 125~245 HV30	A1（ISO 3506-1）硬度 210~280 HV30
6H（ISO 965-2）
Plain, i.e. pins to be supplied in natural finish treated with a protective lubricant, unless otherwise specified by agreement between customer and suppller. Preferred coatings are black oxide, phosphate coating or zinc plating with chromate conversion coating (see ISO 9717 and ISO 4042). 其他表面镀层或表面处理应由供需双方协议。所有公差仅适用于涂、镀前的公差。	Plain, i.e. pins to be supplied in natural finish.
Ra ≤ 0.8 µm
不允许有不规则的和有害的缺陷。销的任何部位不得有毛刺
ISO 3269
① 其他材料由供需双方协议

引用参考

GB /T 1172

黑色金属硬度及强度换算值

GB /T 5267.1 - 2002

镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能

GB /T 193 - 2003

普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)

注：技术数据仅供参考，请以官方原件为准！

告诉我在“易紧通”看到，将给您优惠

上海志宥五金有限公司

联系人：李国志

364950872 移动电话： 15221513104 电话：021-67636815 微信号：15221513104 Email:

登陆后可见

材质：45#、Gcr15、轴承钢(硬度HRC58-62)、304、316；公称直径范围：1-50，公称长度范围:5-500mm 表面处理：磨光，洗光，发黑；现货供应，提供非标定制。

[询价]

类似标准及供货信息

1	[国标] GB /T 120.1 - 2000	不淬硬钢和奥氏体不锈钢内螺纹圆柱销 Parallel Pins With Internal Thread,Of Unhardened Steel And Austenitic Stainless Steel 供应商(10)
2	[国标] GB /T 120.2 - 2000	淬硬钢和马氏体不锈钢内螺纹圆柱销 Parallel Pins With Internal Thread,Of Hardened Steel And Martensitic Stainless Steel 供应商(10)
3	[国标] GB 120 - 1986	内螺纹圆柱销 Parallel Pins With Internal Thread 供应商(10)
4	[德标] DIN 7979 - 1977	内螺纹圆柱销 Parallel Pins With Internal Thread 供应商(5)
5	[国际] ISO 8735 - 1997	淬硬钢和马氏体不锈钢内螺纹圆柱销 Parallel Pins With Internal Thread,Of Hardened Steel And Martensitic Stainless Steel 供应商(2)
6	[国际] ISO 8735 - 1987	内螺纹圆柱销 Parallel Pins With Internal Thread, Of Hardened Steel And Martensitic Stainless Steel 供应商(2)
7	[国际] ISO 8733 - 1986	不淬硬内螺纹圆柱销 Parallel Pins With Internal Thread, Unhardened Steel And Austenitic Stainless Steel 供应商(1)
8	[日标] JIS B 1359 - 2012	1型内螺纹圆柱销 Table 2 Parallel Pins With Internal Thread Of Class 1
9	[日标] JIS B 1359 - 2012	2型内螺纹圆柱销 Table 3 Parallel Pins With Internal Thread Of Class 2
10	[日标] JIS B 1359 - 1990	1型内螺纹圆柱销 Parallel pins with internal thread
11	[日标] JIS B 1359 - 1990	2型内螺纹圆柱销 Parallel Pins With Internal Thread Of Class 2
12	[欧标] EN 28735 - 1992	淬硬内螺纹圆柱销 Hardened Parallel Pins with Internal Thread
13	[法国] NF E 25-755 - 1997 (R2005)	不淬硬钢和奥氏体不锈钢内螺纹圆柱销 Parallel Pins With Internal Thread,of Unhardened Steel And Austenitic Stainless Steel
14	[法国] NF E 25-757 - 1997 (R2002)	淬硬钢和马氏体不锈钢内螺纹圆柱销 Parallel Pins With Internal Thread, Of Hardened Steel And Martensitic Stainless Steel
15	[台湾] CNS 8779 - 1982	内螺纹圆柱销 Parallel Pins With Internal Thread
16	[韩标] KS B 1309 - 2000 (R2020)	内螺纹圆柱销淬硬 Parallel Pins With Internal Thread,of Hardened Steel And Martensitic Stainless Steel
17	[德标] DIN EN 28733 - 1992	内螺纹圆柱销 Parallel Pins With Internal Thread-Unhardened 供应商(5)
18	[德标] DIN EN ISO 8733 - 1998	不淬硬钢和奥氏体不锈钢内螺纹圆柱销 Parallel Pins With Internal Thread-Unhardened Steel And Austenitic Stainless Steel 供应商(5)
19	[德标] DIN EN ISO 8735 - 1998	内螺纹圆柱销 Parallel Pins with Internal Thread of Hardened Steel and Martensitic Stainless Steel 供应商(5)