会员中心 | English | 繁體中文

十字槽球面圆柱头 AB ABR自攻螺钉 ASME B 18.6.3 (H6B-III+T1A) - 2024

选择规格尺寸点击↓

10#

12#

1/4

5/16

3/8

ASME B 18.6.3 (H6B-III+T1A) - 2024 十字槽球面圆柱头 AB ABR自攻螺钉

尺寸单位: inch

美标ASME B18.6.3 (H6B-III+T1A) - 2024 ASME 十字槽球面圆柱头 AB ABR自攻螺钉

扫一扫分享

公差最小破坏扭矩牌号等级

螺纹尺寸
d

10#

12#

1/4

5/16

3/8

d	公称
PP
槽号
M
P	最大值
	最小值
d_k	最大值
	最小值
k₁	最大值
	最小值
k	最大值
	最小值
L₀ ^⑥	公称
Y ^⑥	螺纹过渡长度(全螺纹)	最大值
b ^⑥	螺纹长度 (长螺钉)	最小值

0.0860	0.0990	0.1120	0.1250	0.1380	0.1510	0.1640	0.1900	0.2160	0.2500	0.3125	0.3750
32	28	24	20	20	19	18	16	14	14	12	12
00	0	0	1R	1R	1R	2R	2R	3R	3R	4R	4R
0.050	0.070	0.070	0.091	0.091	0.091	0.112	0.112	0.133	0.133	0.191	0.191
0.033	0.038	0.038	0.065	0.065	0.065	0.075	0.075	0.095	0.095	0.100	0.100
0.028	0.028	0.028	0.050	0.050	0.050	0.060	0.060	0.080	0.080	0.085	0.085
0.140	0.161	0.183	0.205	0.226	0.248	0.270	0.313	0.357	0.414	0.518	0.622
0.124	0.145	0.166	0.187	0.208	0.229	0.250	0.292	0.334	0.389	0.490	0.590
0.062	0.070	0.079	0.088	0.096	0.105	0.113	0.130	0.148	0.170	0.211	0.253
0.053	0.061	0.069	0.078	0.086	0.094	0.102	0.118	0.134	0.155	0.194	0.233
0.083	0.095	0.107	0.120	0.132	0.144	0.156	0.180	0.205	0.237	0.295	0.355
0.066	0.077	0.088	0.100	0.111	0.122	0.133	0.156	0.178	0.207	0.262	0.315
5/8	3/4	13/16	15/16	1	1-1/8	1-1/4	1-3/8	1-5/8	1-13/16	1-13/16	1-7/8
0.031	0.036	0.042	0.050	0.050	0.053	0.056	0.062	0.071	0.071	0.083	0.083
0.520	0.590	0.670	0.750	0.830	0.910	0.980	1.140	1.300	1.500	1.500	1.500

①,若以小数规定公称直径，应省略小数前和小数点后第四位的零。
②,方槽内壁略带锥度，以保证插入深量规与有镀层螺钉凹槽的配合。为使插入深测量深度适用于有涂镀层的螺钉，制造者在生产（镦头）时，应为其留出必要的加工余量。
③,表中的“R”表示正常插入深入。
④,螺钉末端钉尖上不允许因螺纹辗压而形成的虚尖，允许略带圆弧或圆钝形末端。
⑤,小于等于8#的螺钉，螺纹牙顶平面宽度不应超过0.004in，大于8#的应不超过0.006in。
⑥,正常情况下，当螺钉长度小于等于其公称长度L0时应采用全螺纹，过渡螺纹长度应小于等于Y；若螺钉长度大于其公称长度L0可采用半牙型式，但其螺纹长度应不小于b。

替代列表

ASME B 18.6.3T22-III+T40 - 2013 ASME B 18.6.3H6B-III+T1A - 2024

引用参考

GB /T 1172 - 1999

黑色金属硬度及强度换算值

GB /T 5267.1 - 2002

镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能

GB /T 193 - 2003

普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)

GB /T 3106 - 2016

紧固件 - 螺栓、螺钉和螺柱 - 公称长度和螺纹长度 (ISO 888:2012, MOD)

GB /T 3 - 1997

普通螺纹收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983)

GB /T 5779.1 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 一般要求

GB /T 5779.3 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 特殊要求

注：技术数据仅供参考，请以官方原件为准！

类似标准及供货信息

1	[万禧] WS 9200 - 2014	内六角圆柱头自攻螺钉 Hexagon socket cheese head self-tapping screws
2	[美标] ASME B 18.6.5M (T11) - 2000	米制四方槽沉头自攻钉 [Table 11] Metric square recessed flat countersunk tapping screws [Table 11] 供应商(2)
3	[美标] ASME B 18.6.5M (T11) - 2000 (R2010)	米制四方槽沉头自攻钉 [Table 11] Metric Type Ill Square-Recessed Flat Countersunk Head Tapping Screws [Table 11] 供应商(2)
4	[美标] ASME B 18.6.3 (H1B-III+T1A) - 2024	四方槽沉头螺钉 (ASTM F837, F468) Square Recessed Countersunk Head Screws (ASTM F837, F468)
5	[美标] ASME B 18.6.3 (H2B-III+T1A) - 2024	四方槽半沉头 AB ABR自攻螺钉 Square recessed raised countersunk head tapping screws - Type AB and ABR
6	[美标] ASME B 18.6.3 (H3B-III+T1A) - 2024	方槽82°沉头清根 AB ABR自攻螺钉 Undercut 82-deg Square Recessed Countersunk Head Tapping Screws - Type AB (ABR)
7	[美标] ASME B 18.6.3 (H3D-III+T1A) - 2024	四方槽82°半沉头清根 AB ABR自攻螺钉 Square recessed undercut oval countersunk head tapping screws - Type AB and ABR
8	[美标] ASME B 18.6.3 (H5C-III+T1A) - 2024	四方槽盘头 AB ABR自攻螺钉 Square Recessed Pan Head Tapping Screws - Type AB and ABR
9	[美标] ASME B 18.6.3 (H7B-III+T1A) - 2024	四方槽大扁头 AB ABR自攻螺钉 Square Recessed Mushroom Head Tapping Screws - Type AB and ABR
10	[美标] ASME B 18.6.3 (H11B-III+T1A) - 2024	方槽圆头 AB ABR自攻螺钉 Square Recessed Round Head Tapping Screws - Type AB and ABR
11	[美标] ASME B 18.6.3 (T2-III+T40) - 2013	方槽82度沉头AB ABR自攻螺钉 82° Square Recessed Countersunk Head Tapping Screws - Type AB (ABR)
12	[美标] ASME B 18.6.3 (T10-III+T40) - 2013	方槽82°沉头清根 AB ABR自攻螺钉 Undercut 82-deg Square Recessed Countersunk Head Tapping Screws - Type AB (ABR)
13	[美标] ASME B 18.6.3 (T8-III+T40) - 2013	四方槽半沉头 AB ABR自攻螺钉 Square recessed raised countersunk head tapping screws - Type AB and ABR
14	[美标] ASME B 18.6.3 (T12-III+T40) - 2013	四方槽82°半沉头清根 AB ABR自攻螺钉 Square recessed undercut oval countersunk head tapping screws - Type AB and ABR
15	[美标] ASME B 18.6.3 (T19-III+T40) - 2013	四方槽盘头 AB ABR自攻螺钉 Square Recessed Pan Head Tapping Screws - Type AB and ABR
16	[美标] ASME B 18.6.3 (T22-III+T40) - 2013	四方槽球面圆柱头 AB ABR自攻螺钉 Square Recessed Raised Cheese Head Tapping Screws - Type AB and ABR
17	[美标] ASME B 18.6.3 (T25-III+T40) - 2013	四方槽大扁头 AB ABR自攻螺钉 Square Recessed Mushroom Head Tapping Screws - Type AB and ABR
18	[美标] ASME B 18.6.3 (T36-III+T40) - 2013	方槽圆头 AB ABR自攻螺钉 Square Recessed Round Head Tapping Screws - Type AB and ABR
19	[美标] ASME B 18.6.5M (T19) - 2000	米制四方槽盘头自攻螺钉 [Table 19] Metric square slot pan head tapping screws [Table 19]
20	[美标] ASME B 18.6.5M (T15) - 2000 (R2010)	米制四方槽半沉头自攻钉 [Table 15] Metric Type III square-recessed oval countersunk head tapping screws
21	[美标] ASME B 18.6.5M (T19) - 2000 (R2010)	米制四方槽盘头自攻螺钉 [Table 19] Metric Type Ill Square-Recessed Pan Head Tapping Screws [Table 19]