index
logo

80° 开槽半沉头清根 AB、ABR型自攻螺钉 ASME B 18.6.3 (H3C+T1A) - 2024

选择规格尺寸 点击↓

0#

1#

2#

3#

4#

5#

6#

7#

8#

10#

12#

1/4

5/16

3/8

7/16

1/2

ASME B 18.6.3 (H3C+T1A) - 2024 80° 开槽半沉头清根 AB、ABR型自攻螺钉

尺寸单位: inch
美标ASME B18.6.3 (H3C+T1A) - 2024 ASME18.6 80° 开槽半沉头清根 AB、ABR型自攻螺钉
ASME B 18.6.3 (H3C+T1A) - 2024 80° 开槽半沉头清根 AB、ABR型自攻螺钉
扫一扫分享
螺纹尺寸
d
0# 1# 2# 3# 4# 5# 6# 7#
d 公称
PP
dk 最大值
最小值
k 参考值
f 参考值
n 最大值
最小值
t 最大值
最小值
α 最大值
最小值
L0 公称
Y 螺纹过渡长度(全螺纹) 最大值
b 螺纹长度 (长螺钉) 最小值
0.0600 0.0730 0.0860 0.0990 0.1120 0.1250 0.1380 0.1510
48 42 32 28 24 20 20 19
0.112 0.137 0.162 0.187 0.212 0.237 0.262 0.287
0.096 0.120 0.144 0.167 0.191 0.215 0.238 0.262
0.025 0.031 0.036 0.042 0.047 0.053 0.059 0.064
0.021 0.025 0.029 0.033 0.037 0.041 0.045 0.049
0.023 0.026 0.031 0.035 0.039 0.043 0.048 0.048
0.016 0.019 0.023 0.027 0.031 0.035 0.039 0.039
0.028 0.034 0.040 0.047 0.053 0.059 0.065 0.071
0.022 0.027 0.033 0.038 0.043 0.048 0.053 0.059
82° 82° 82° 82° 82° 82° 82° 82°
80° 80° 80° 80° 80° 80° 80° 80°
7/16 9/16 5/8 3/4 13/16 15/16 1 1-1/8
0.021 0.024 0.031 0.036 0.042 0.050 0.050 0.053
0.360 0.440 0.520 0.590 0.670 0.750 0.830 0.910
螺纹尺寸
d
8# 10# 12# 1/4 5/16 3/8 7/16 1/2
d 公称
PP
dk 最大值
最小值
k 参考值
f 参考值
n 最大值
最小值
t 最大值
最小值
α 最大值
最小值
L0 公称
Y 螺纹过渡长度(全螺纹) 最大值
b 螺纹长度 (长螺钉) 最小值
0.1640 0.1900 0.2160 0.2500 0.3125 0.3750 0.4375 0.5000
18 16 14 14 12 12 10 10
0.312 0.362 0.412 0.477 0.597 0.717 0.760 0.815
0.285 0.333 0.380 0.442 0.556 0.670 0.715 0.765
0.070 0.081 0.092 0.107 0.134 0.161 0.156 0.156
0.052 0.060 0.068 0.079 0.099 0.117 0.122 0.131
0.054 0.060 0.067 0.075 0.084 0.094 0.094 0.106
0.045 0.050 0.056 0.064 0.072 0.081 0.081 0.091
0.078 0.090 0.103 0.119 0.149 0.179 0.184 0.204
0.064 0.074 0.085 0.098 0.124 0.149 0.154 0.169
82° 82° 82° 82° 82° 82° 82° 82°
80° 80° 80° 80° 80° 80° 80° 80°
1-1/4 1-3/8 1-5/8 1-13/16 1-13/16 1-7/8 1-7/8 1-7/8
0.056 0.062 0.071 0.071 0.083 0.083 0.100 0.100
0.980 1.140 1.300 1.500 1.500 1.500 1.500 1.500
①,正常情况下,当螺钉长度小于等于其公称长度L0时应采用全螺纹,过渡螺纹长度应小于等于Y;若螺钉长度大于其公称长度L0可采用半牙型式,但其螺纹长度应不小于b。
替代列表

长度公差

  Tapping screws can be made to any length, but they are generally produced in fractional length increments of 1/16 in. for screws up to 1/2 in. long, 1/8 in. for screws over 1/2 in. through 1-1/2 in. long, 1/4 in. for screws over 1-1/2 in. through 3 in. long, and 1/2 in. for screws over 3 in. long.

类型

标称螺钉长度

长度公差

AABBP

1

±0.03

1

±0.05

BBFBTCDFGTTRS

3/4

-0.03

3/4,1-1/2

-0.05

1-1/2

-0.06

注:技术数据仅供参考,请以官方原件为准!
类似标准及供货信息
1 开槽半沉头自攻螺钉 [国标]
GB /T 5284 - 2017
开槽半沉头自攻螺钉
Slotted Raised Countersunk(Oval) Head Tapping Screws
2 开槽半沉头自攻螺钉 [国标]
GB /T 5284 - 1985
开槽半沉头自攻螺钉
Slotted Raised Countersunk Head Tapping Screws
3 米制开槽半沉头自攻钉 [美标]
IFI 502 - 1982
米制开槽半沉头自攻钉
Metric Slotted Oval Countersunk Head Tapping Screws
4 开槽半沉头自攻螺钉 [德标]
DIN 7973 - 1990
开槽半沉头自攻螺钉
Slotted Raised Countersunk Head Tapping Screws
供应商(3)
5 开槽半沉头自攻螺钉 [国际]
ISO 1483 - 2011
开槽半沉头自攻螺钉
Slotted Raised Countersunk (Oval) Head Tapping Screws
6 开槽接骨螺钉 HC螺纹 [Figure 1] [国际]
ISO 9268 (F1) - 1988
开槽接骨螺钉 HC螺纹 [Figure 1]
Metal bone Screw with Single-slot Recess, with Symmetrical Thread Form HC [Figure 1]
7 开槽半沉头自攻螺钉 [国际]
ISO 1483 - 1983
开槽半沉头自攻螺钉
Slotted raised countersunk head tapping screws
8 开槽半沉头自攻螺钉 [Table 9] [日标]
JIS B 1115 (T9) - 2015
开槽半沉头自攻螺钉 [Table 9]
Slotted Raised Countersunk Head Tapping Screws [Table 9]
9 开槽半沉头自攻钉 [表JA5] [日标]
JIS B 1115 (JA5) - 2015
开槽半沉头自攻钉 [表JA5]
Slotted Raised countersunk head tapping screws [Table JA5]
10 开槽半沉头自攻钉 [表3] [日标]
JIS B 1115 (T3) - 1996
开槽半沉头自攻钉 [表3]
Slotted raised countersunk head tapping screws [Table 3]
11 开槽半沉头自攻钉 [附表3] [日标]
JIS B 1115 (AT3) - 1996
开槽半沉头自攻钉 [附表3]
Slotted Raised countersunk head tapping screws [Annex Table 3]
12 80°开槽半沉头自攻钉 [美标]
ASME/ANSI B 18.6.3 - 2010
80°开槽半沉头自攻钉
80° Machine Screw and Tapping Screw Nuts (Inch Seires)
13 开槽半沉头自攻螺钉 [法国]
NF E 25-661 - 1994
开槽半沉头自攻螺钉
Slotted Raised Countersunk (Oval) Head Tapping Screws
14 开槽80°半沉头自攻钉 [Table 12] [英标]
BS 4174 - 1972
开槽80°半沉头自攻钉 [Table 12]
80°Slotted Raised Countersunk Head Tapping Screws [Table 12]
15 米字槽80°半沉头自攻钉 [Table 13] [英标]
BS 4174 - 1972
米字槽80°半沉头自攻钉 [Table 13]
Cross Recess 80° Raised Countersunk Head Tapping Screws [Table 13]
16 开槽80°半沉头清根自攻钉 [Table 14] [英标]
BS 4174 - 1972
开槽80°半沉头清根自攻钉 [Table 14]
Slotted 80° truncated Raised Countersunk Head Screws [Table 14]
17 米制开槽半沉头自攻螺钉 [澳标]
AS /NZS 4405 - 1996
米制开槽半沉头自攻螺钉
ISO metric slotted raised countersunk head tapping screws
18 开槽半沉头自攻螺钉 [德标]
DIN EN ISO 1483 - 2011
开槽半沉头自攻螺钉
Slotted Raised Countersunk (Oval) Head Tapping Screws
供应商(3)
19 82°开槽半沉头 AB ABR 自攻螺钉 [美标]
ASME B 18.6.3 (H2A+T1A) - 2024
82°开槽半沉头 AB ABR 自攻螺钉
82° Dimensions of Slotted Oval Countersunk Head Tapping Screws
20 82°开槽半沉头 AB ABR 自攻螺钉 [Table 7] [美标]
ASME B 18.6.3 (T7+T40) - 2013
82°开槽半沉头 AB ABR 自攻螺钉 [Table 7]
82° Dimensions of Slotted Oval Countersunk Head Tapping Screws [Table 7]
21 80° 开槽半沉头清根自攻螺钉 [Table 11] [美标]
ASME B 18.6.3 (T11t) - 2013
80° 开槽半沉头清根自攻螺钉 [Table 11]
80° Slotted Undercut Oval Countersunk Head Tapping Screws [Table 11]
22 米制开槽半沉头自攻钉 [Table 12] [美标]
ASME B 18.6.5M (T12) - 2000 (R2010)
米制开槽半沉头自攻钉 [Table 12]
Metrice slotted raised countersunk head tapping screws [Table 12]
23 开槽半沉头自攻螺钉 B,BP型 [Table 20] [美标]
ASME B 18.6.4 - 1998 (R2005)
开槽半沉头自攻螺钉 B,BP型 [Table 20]
slotted Oval Countersunk Head Tapping Screws - Type B and BP Thread Forming [Table 20]
24 开槽半沉头自攻螺钉 C型(统一螺纹) [Table 20] [美标]
ASME B 18.6.4 - 1998 (R2005)
开槽半沉头自攻螺钉 C型(统一螺纹) [Table 20]
slotted Oval Countersunk Head Tapping Screws - Type C Thread Forming [Table 20]
25 开槽半沉头自攻螺钉 AB型 [Table 20] [美标]
ASME B 18.6.4 - 1998 (R2005)
开槽半沉头自攻螺钉 AB型 [Table 20]
slotted Oval Countersunk Head Tapping Screws - Type AB Thread Forming [Table 20]
26 开槽半沉头自攻螺钉 A型 [Table 20] [美标]
ASME B 18.6.4 - 1998 (R2005)
开槽半沉头自攻螺钉 A型 [Table 20]
slotted Oval Countersunk Head Tapping Screws - Type A Thread Forming [Table 20]
27 HC型开槽接骨螺钉 [Table 6] [医药行业标准]
YY 0018 (T6) - 2016
HC型开槽接骨螺钉 [Table 6]
Metal bone Screw with Single-slot Recess, with Symmetrical Thread Form HC [Table 6]
© 易紧通 服务热线:4006-164580(免长途费)