会员中心 | English | 繁體中文

眼镜框架用 - 十一字槽平头螺钉 JIS B 1119 (2F) - 1986

选择规格尺寸点击↓

M1 ×1.8

M1.2 ×2

M1.4 ×2

M1.4 ×2.5

M1.6 ×2.5

(M1.7) ×2.5

括号内尺寸为非优选

尺寸单位: mm

日标JIS B1119 (2F) - 1986 JIS1119 1119JIS 眼镜框架用 - 十一字槽平头螺钉

扫一扫分享

公差公制螺纹极限尺寸米/英制螺纹对照螺纹直径与受力截面积最小破坏扭矩牌号等级毛坯直径

螺纹尺寸
d

M1
×1.8

M1.2
×2

M1.4
×2

M1.4
×2.5

M1.6
×2.5

(M1.7)
×2.5

P	螺距
d_k	公称
	最大值
	最小值
k	公称
	最大值
	最小值
n	最大值
n	最小值
t	公称
	最大值
	最小值
r	最大值

0.25	0.25	0.3	0.3	0.35	0.35
1.8	2	2	2.5	2.5	2.5
1.85	2.05	2.05	2.55	2.55	2.55
1.7	1.9	1.9	2.4	2.4	2.4
0.8	0.8	0.8	0.8	0.8	0.8
0.88	0.88	0.88	0.88	0.88	0.88
0.72	0.72	0.72	0.72	0.72	0.72
0.45	0.45	0.45	0.45	0.45	0.45
0.32	0.32	0.32	0.32	0.32	0.32
0.35	0.35	0.35	0.35	0.35	0.35
0.43	0.43	0.43	0.43	0.43	0.43
0.27	0.27	0.27	0.27	0.27	0.27
0.1	0.1	0.1	0.1	0.1	0.1

①,螺纹长度（b）应在交付时由相关各方商定。
②,槽型尺寸应遵循标准：JIS B 1012 - S型

引用参考

GB /T 1172 - 1999

黑色金属硬度及强度换算值

GB /T 5267.1 - 2002

镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能

GB /T 193 - 2003

普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)

GB /T 3106 - 2016

紧固件 - 螺栓、螺钉和螺柱 - 公称长度和螺纹长度 (ISO 888:2012, MOD)

GB /T 3 - 1997

普通螺纹收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983)

GB /T 5779.1 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 一般要求

GB /T 5779.3 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 特殊要求

注：技术数据仅供参考，请以官方原件为准！

类似标准及供货信息

1	[国标] GB /T 822 - 2016	十字槽圆柱头螺钉 Cheese Head Screws with Cross Recess 供应商(1)
2	[国标] GB /T 822 - 2000	十字槽圆柱头螺钉 Cheese Head Screws with Cross Recess 供应商(1)
3	[国标] GB /T 13806.1 (A) - 1992	精密机械用紧固件十字槽圆柱头螺钉 Cheese Head Screws With Cross Recess For Fine Mechanics 供应商(1)
4	[国标] GB /T 822 - 1988	十字槽圆柱头螺钉 Cross Recessed Cheese Head Serews 供应商(1)
5	[国标] GB 945 - 1976	十字槽球面圆柱头螺钉 Cross Recessed Fillister Head Screws
6	[德标] DIN 7964 (C) - 1990	粗牙不脱出螺栓和螺钉 - 十字槽矮圆柱头 Reduced shanke bolts and screws with coarse thread - Cross recessed raised cheese head 供应商(4)
7	[德标] DIN 7985 - 1986	十字槽球面(矮)圆柱头螺钉 Cross recessed raised cheese head screws 供应商(6)
8	[德标] DIN 34813 - 1999	塑料十字槽圆柱头螺钉 Plastic Cross Recessed Cheese Head Screws
9	[国际] ISO 7048 - 2011	十字槽圆柱头螺钉 Cross Recessed Cheese Head Screws 供应商(1)
10	[国际] ISO 7048 - 1998	十字槽圆柱头螺钉 Cross Recessed Cheese Head Screws 供应商(1)
11	[日标] JIS B 1111 (JA7) - 2017	十字槽球面圆柱头螺钉 [附属表 JA.7] Cross Recessed Raised Cheese Head Screws 供应商(1)
12	[日标] JIS B 1111 (A5) - 2006	十字槽球面圆柱头螺钉附属表5 Cross Recessed Raised Cheese Head Screws 供应商(1)
13	[日标] JIS B 1111 (A5) - 1996	十字槽球面圆柱头螺钉附属表5 Cross recessed raised cheese head screws 供应商(1)
14	[日标] JIS B 1111 (T14) - 2017	十字槽圆柱头螺钉 [表14] Cross Recessed Cheese Head Screws
15	[美标] ASME/ANSI B 18.6.3 (T22) - 2010	十字槽球面圆柱头螺钉Table22 Cross Recessed Raised Cheese Head Machine Screws
16	[法国] NF E 25-149 - 1998 (R2004)	十字槽圆柱头螺钉 Cross Recessed Cheese Head Screws
17	[英标] BS 1981 - 1991	米字槽球面圆柱头螺钉Table15 Cross Raised Cheese Head Screws
18	[英标] BS 450 - 1958	英制十字槽球面圆柱头螺钉 - B.S.W. & B.S.F. 螺纹 [Table 7] Cross Recessed Raised Cheese Head Screws with B.S.W. & B.S.F. Threads [Table 7]
19	[电力] DL /T 1496 - 2016	电能计量封印技术规范 - 卡扣式封印螺钉 ELectrical energy metering seal technical specification
20	[德标] DIN EN ISO 7048 - 2011	十字槽矮圆柱头螺钉 Cross-Recessed Cheese Head Screws
21	[美标] ASME B 18.6.3 (H6B-I/H6B-IA) - 2024	十字槽球面圆柱头螺钉 [TABLE 2.2.6-2 I/IA] Cross recessed raised Fillister head screws [TABLE 2.2.6-2 I/IA]
22	[美标] ASME B 18.6.3 (H8B-I/H8B-IA) - 2024	十字槽球面圆柱头螺钉 [TABLE 2.2.8-2 I/IA] Cross Recessed Raised Binding Head Screws [TABLE 2.2.8-2 I/IA]
23	[美标] ASME B 18.6.3 (T22-I/T22-IA) - 2013	十字槽球面圆柱头螺钉 Cross recessed raised cheese head screws
24	[美标] ASME B 18.6.3 (T28-I/T28-IA) - 2013	十字槽球面圆柱头螺钉 Cross recessed raised cheese head screws