index
会员中心 | English | 繁體中文
logo
首页 产品与标准 HB 7196~7199 (7196/7197/7198/7199) - 1995 十字槽100°沉头螺钉（带孔或不带孔）

十字槽100°沉头螺钉（带孔或不带孔） HB 7196~7199 (7196/7197/7198/7199) - 1995

选择规格尺寸 点击↓

M4

M5

M6

M8

M10

HB 7196~7199 (7196/7197/7198/7199) - 1995 十字槽100°沉头螺钉（带孔或不带孔）

尺寸单位: mm
航空HB 7196~7199 (7196/7197/7198/7199) - 1 十字槽100°沉头螺钉（带孔或不带孔）
HB 7196~7199 (7196/7197/7198/7199) - 1995 十字槽100°沉头螺钉（带孔或不带孔）
扫一扫分享
公差 公制螺纹极限尺寸 米/英制螺纹对照 螺纹直径与受力截面积 最小破坏扭矩 牌号等级 毛坯直径
螺纹尺寸
d
M4 M5 M6 M8 M10
d1 ① 最大值=公称
最小值
H 参考
D 参考
D1 最小值
D2 供测量用
b 参考
P2 最大值
最小值
r 最大值
最小值
d2
C 参考
4 5 6 8 10
3.88 4.88 5.88 7.85 9.85
1.68 2.11 2.53 3.38 4.23
8 10 12 16 20
7.2 9 10.8 14.8 18.8
5.78 7.71 9 12.21 15.46
7.5 8.5 10 11.5 15
0.93 0.96 1.26 1.6 1.93
0.85 0.88 1.18 1.52 1.85
0.4 0.5 0.7 0.7 0.8
0.2 0.3 0.5 0.5 0.6
1 1.6 1.6 2 2.5
2.5 3 3 4 4
①,ML25和铝合金制螺栓，光杆直径d1允许等于滚制或切制螺纹前的毛坯尺寸。
②,标志按 HB 0-3-83；十字槽按 HT2GB944-76 (d1=5mm时，T2=1.8mm，3号槽)；重量按 HB 1-143-95；接力试验载荷按 HB 1-217-95；技术条件按 HB 1-218-95。
③,HB 7196：材料 ML25，镀锌钝化。标记示例 d1=6/L=36/C=3 (无销孔 HB 7196-6×36，有销孔 HB 7196-6×36×3) 。
④,HB 7197：材料 ML30CrMnSiA；热处理 σb=1175±100 MPa；d1≤8 镀锌钝化，d1=10 镀镉钝化。标记示例 d1=6/L=36/C=3 (无销孔 HB 7197-6×36，有销孔 HB 7197-6×36×3) 。
⑤,HB 7198：材料 1Cr17Ni2；热处理 σb=1175±100 MPa；钝化。标记示例 d1=6/L=36/C=3 (无销孔 HB 7198-6×36，有销孔 HB 7198-6×36×3) 。
⑥,HB 7199：材料 LY8；热处理 σb≥375 MPa；阳极化。标记示例 d1=6/L=36/C=3 (无销孔 HB 7199-6×36，有销孔 HB 7199-6×36×3) 。

相关材料标准或牌号

GB /T 700-2006
牌号
中国ISC
旧牌号
其他名称
GB /T 699-2015
牌号
中国ISC
其他名称
GB /T 699-2015
牌号
中国ISC
其他名称
GB /T 11352-2009
牌号
旧牌号

引用参考

GB /T 1172 - 1999
黑色金属硬度及强度换算值
GB /T 5267.1 - 2002
镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能
GB /T 193 - 2003
普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)
GB /T 3106 - 2016
紧固件 - 螺栓、螺钉和螺柱 - 公称长度和螺纹长度 (ISO 888:2012, MOD)
GB /T 3 - 1997
普通螺纹收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983)
GB /T 5779.1 - 2000
紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 一般要求
GB /T 5779.3 - 2000
紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 特殊要求
GB /T 3103.1 - 2002
紧固件公差（螺栓、螺柱、螺钉和螺母）
GB /T 34632 - 2017
统一螺纹搓制和滚制前的毛坯直径
GB /T 18685 - 2017
普通螺纹搓制和滚制前的毛坯直径
GB /T 3105 - 2002
普通螺栓和螺钉 - 头下圆角半径
GB /T 5279.2 - 1997
沉头螺钉 第2部分 十字槽插入深度
GB /T 197 - 2018
普通螺纹 公差
注：技术数据仅供参考，请以官方原件为准！
类似标准及供货信息
1 十字槽沉头螺钉 第1部分：4.8级 [国标]
GB /T 819.1 - 2016		 十字槽沉头螺钉 第1部分：4.8级
Countersunk Flat Head Screws (Common Head Style) with Cross Recess - Part 1: Property Class 4.8
供应商(13)
2 十字槽沉头螺钉 第2部分：8.8级、不锈钢及有色金属螺钉 [国标]
GB /T 819.2 - 2016		 十字槽沉头螺钉 第2部分：8.8级、不锈钢及有色金属螺钉
Countersunk Flat Head Screws with Cross Recess - Part 2: Property Class 8.8, Stainless Steel Screws and Non-ferrous Metal Screws
供应商(1)
3 十字槽沉头螺钉 4.8级 [国标]
GB /T 819.1 - 2000		 十字槽沉头螺钉 4.8级
Countersunk Flat Head Screws (Common Head Style) with Cross Recess - Part 1: Property Class 4.8
供应商(13)
4 十字槽沉头螺钉 第2部分：钢8.8级、不锈钢A2-70和有色金属螺钉CU2或CU3 [国标]
GB /T 819.2 - 1997		 十字槽沉头螺钉 第2部分：钢8.8级、不锈钢A2-70和有色金属螺钉CU2或CU3
Cross Recessed Countersunk Flat Head Screws (Common Head Style) - Grade A - Part 2: Steel of Property Class 8.8, Stainless and Non-Ferrous Metals
供应商(1)
5 精密机械用紧固件十字槽沉头螺钉 [国标]
GB /T 13806.1 (B) - 1992		 精密机械用紧固件十字槽沉头螺钉
Cross Recessed Countersunk Screws For Fine Mechanics
供应商(1)
6 十字槽沉头螺钉 [国标]
GB 819 - 1985		 十字槽沉头螺钉
Cross Recessed Countersunk Head Screws
供应商(13)
7 十字槽沉头螺钉 [国标]
GB 819 - 1976		 十字槽沉头螺钉
Cross recessed countersunk head screws
供应商(13)
8 十字槽沉头螺钉 [德标]
DIN 965 - 1990		 十字槽沉头螺钉
Cross Recessed Countersunk Head Screws
供应商(6)
9 塑料米字槽沉头螺钉 [德标]
DIN 34811 - 1999		 塑料米字槽沉头螺钉
Plastic Flat Head Screws With Cross Recess
10 8.8 级、不锈钢及有色金属 十字槽沉头螺钉 [国际]
ISO 7046 (-2) - 2011		 8.8 级、不锈钢及有色金属 十字槽沉头螺钉
Countersunk Flat Head Screws(Common Head Style) With Type H Or Type Z Cross Recess-Product Grade A-Property Class 8.8
供应商(1)
11 8.8 级、不锈钢及有色金属 十字槽沉头螺钉 [国际]
ISO 7046-2 - 1990		 8.8 级、不锈钢及有色金属 十字槽沉头螺钉
Cross Recessed Countersunk Flat Head Screws(common Head Style) - Grade A - Steel Of Property Class 8.8,stainless Steel And Nonferrous Metals
供应商(1)
12 4.8级十字槽沉头螺钉 [国际]
ISO 7046 (-1) - 2011		 4.8级十字槽沉头螺钉
Countersunk Flat Head Screws(Common Head Style)With Type H Or Type Z Cross Recess- Product Grade A-Steel Screws Of Property Class 4.8
13 航空航天 强度≤1100Mpa 金属材料 标准杆 短或中等长度MJ螺纹 偏十字槽 100°沉头螺钉 [国际]
ISO 5856 - 2008		 航空航天 强度≤1100Mpa 金属材料 标准杆 短或中等长度MJ螺纹 偏十字槽 100°沉头螺钉
Aerospace - Screws, 100 degrees normal countersunk head, internal offset cruciform ribbed or unribbed drive, normal shank, short or medium length MJ threads, metallic material, coated or uncoated, strength classes less than or equal to 1 100 MPa - Dimensi
14 十字槽沉头螺钉 [国际]
ISO 7046-1 - 1994		 十字槽沉头螺钉
Cross recessed countersunk head screws
15 十字槽沉头螺钉 [附属表 JA.4] [日标]
JIS B 1111 (JA4) - 2017		 十字槽沉头螺钉 [附属表 JA.4]
Cross Recessed Countersunk Head Screws
供应商(2)
16 十字槽沉头螺钉 4.8级 [表6] [日标]
JIS B 1111 (T6) - 2017		 十字槽沉头螺钉 4.8级 [表6]
Cross Recessed Countersunk Head Screws - Class 4.8
17 十字槽沉头螺钉 8.8级 [表9] [日标]
JIS B 1111 (T9) - 2017		 十字槽沉头螺钉 8.8级 [表9]
Cross Recessed Countersunk Head Screws - Class 8.8
18 十字槽沉头螺钉 4.8级 [表2] [日标]
JIS B 1111 (T2) - 2006		 十字槽沉头螺钉 4.8级 [表2]
Cross Recessed Countersunk Head Screws - Class 4.8
19 十字槽沉头螺钉 8.8级 [表3] [日标]
JIS B 1111 (T3) - 2006		 十字槽沉头螺钉 8.8级 [表3]
Cross Recessed Countersunk Head Screws - Class 8.8
20 十字槽沉头螺钉 8.8级 [表3] [日标]
JIS B 1111 (T3) - 1996		 十字槽沉头螺钉 8.8级 [表3]
Cross recessed countersunk head screws - Class 8.8
21 十字槽沉头螺钉 4.8级 [表2] [日标]
JIS B 1111 (T2) - 1996		 十字槽沉头螺钉 4.8级 [表2]
Cross recessed countersunk head screws-Class 4.8
22 十字槽沉头螺钉 [汽标代号]
Q 254		 十字槽沉头螺钉
Cross recessed countersunk head screws
23 十字槽沉头螺钉Table2 [美标]
ASME/ANSI B 18.6.3 - 2010		 十字槽沉头螺钉Table2
Cross recessed countersunk head screws
供应商(2)
24 米制十字槽沉头螺钉Table3 [美标]
ASME/ANSI B 18.6.7M - 1998		 米制十字槽沉头螺钉Table3
Metric cross recessed countersunk screws
25 米制米字槽沉头螺钉Table4 [美标]
ASME/ANSI B 18.6.7M - 1998		 米制米字槽沉头螺钉Table4
Metric PZ Drives countersunk head screws
26 航空航天 - 100°沉头螺钉 偏十字槽 镀镉 合金钢 中等螺纹长度 粗公差普通杆 等级：1100MPa(室温)/235℃ [欧标]
EN 4162 - 2016		 航空航天 - 100°沉头螺钉 偏十字槽 镀镉 合金钢 中等螺纹长度 粗公差普通杆 等级：1100MPa(室温)/235℃
Aerospace Series - Screws, 100° Countersunk Normal Head, Offset Cruciform Recess, Coarse Tolerance Normal Shank, Medium Length Thread, in Alloy Steel, Cadmium Plated - 1100 MPa (at Ambient Temperature)/235 °C
27 十字槽沉头螺钉 [意大利]
UNI 7688 - 1977		 十字槽沉头螺钉
Cross Recessed Countersunk Head Screws
28 4.8级十字槽沉头螺钉 [法国]
NF E 25-119-1 - 1994		 4.8级十字槽沉头螺钉
Countesunk Flat Head Screws,with Type H Or Type Z Cross Recessed - Product Grade A, Class 4.8
29 8.8级十字槽沉头螺钉 [法国]
NF E 25-119-2 - 1994		 8.8级十字槽沉头螺钉
Cross Recessed Countersunk Head Screws - Grade A, Class 8.8
30 米字槽沉头螺钉（短的）Table 7 [英标]
BS 1981 - 1991		 米字槽沉头螺钉（短的）Table 7
Recessed Truncated Countersunk Head Screws:short Length
31 米字槽沉头螺钉Table4 [英标]
BS 1981 - 1991		 米字槽沉头螺钉Table4
Recessed Truncated Countersunk Head Screws: Long Length
32 英制十字槽沉头螺钉 - B.S.W. & B.S.F. 螺纹 [Table 2] [英标]
BS 450 - 1958		 英制十字槽沉头螺钉 - B.S.W. & B.S.F. 螺纹 [Table 2]
Cross Recessed 90° Countersunk Head Screws with B.S.W. & B.S.F. Threads [Table 2]
33 米制十字槽沉头螺钉 [Table 1] [澳标]
AS /NZS 1427 - 1996		 米制十字槽沉头螺钉 [Table 1]
ISO metric cross-recess countersunk screws [Table 1]
34 十字槽沉头螺钉 [台湾]
CNS 4560 - 1981		 十字槽沉头螺钉
Cross Recessed Countersunk Head Screws
35 十字槽沉头螺钉 A级和B级 [俄标]
GOST 17475 - 1980		 十字槽沉头螺钉 A级和B级
Countersunk head screws of accuracy classes A and B (Cross Recessed)
36 4.8级十字槽沉头螺钉 [韩标]
KS B 1023 (T7) - 2016 (R2021)		 4.8级十字槽沉头螺钉
Cross Recessed Countersunk Head Screws - Class 4.8
37 8.8级及有色金属十字槽沉头螺钉 [韩标]
KS B 1023 (T8) - 2016 (R2021)		 8.8级及有色金属十字槽沉头螺钉
Non-ferrous Metal Cross Recessed Countersunk Head Screws - Class 8.8
38 4.8级十字槽沉头螺钉 [韩标]
KS B 1023 (T2) - 2001		 4.8级十字槽沉头螺钉
Cross Recessed Countersunk Head Screws - Class 4.8
39 8.8级及有色金属十字槽沉头螺钉 [韩标]
KS B 1023 (T3) - 2001		 8.8级及有色金属十字槽沉头螺钉
Non-ferrous Metal Cross Recessed Countersunk Head Screws - Class 8.8
40 十字槽沉头螺钉（通用头型）- 4.8级，钢制，产品等级A级 [德标]
DIN EN ISO 7046-1 - 2011		 十字槽沉头螺钉（通用头型）- 4.8级，钢制，产品等级A级
Countersunk Flat Head Screws (Common Head Style) with Type H or Type Z Cross Recess - Product Grade A - Part 1: Steel Screws of Property Class 4.8
供应商(6)
41 8.8 级、不锈钢及有色金属 十字槽沉头螺钉 [德标]
DIN EN ISO 7046-2 - 2011		 8.8 级、不锈钢及有色金属 十字槽沉头螺钉
Countersunk Flat Head Screws(common Head Style) With Type H Or Type Z Cross Recess-product Grade A-property Class 8.8
供应商(5)
42 十字槽100°沉头螺栓 [军标]
GJB 3371 (/57~/60) - 1998		 十字槽100°沉头螺栓
Cross Recessed 100° Countersunk Head Screws
43 光杆公差带f9 十字槽100°沉头螺栓 [军标]
GJB 3371 (/62) - 1998		 光杆公差带f9 十字槽100°沉头螺栓
Cross Recessed 100° Countersunk Head Screws，Shank Tolerance f9
44 光杆公差带h8短螺纹十字槽 100°沉头螺栓 [军标]
GJB 3371 (/64) - 1998		 光杆公差带h8短螺纹十字槽 100°沉头螺栓
Cross Recessed 100° Countersunk Head Screws, Short Thread, Shank Tolerance h8
45 十字槽 100°锥端沉头螺栓 [军标]
GJB 3371 (/68) - 1998		 十字槽 100°锥端沉头螺栓
Cross Recessed 100° Countersunk Head Screws With Cone Point
46 光杆公差带r6短螺纹十字槽 100°沉头螺栓 [军标]
GJB 3371 (/84) - 1998		 光杆公差带r6短螺纹十字槽 100°沉头螺栓
Cross Recessed 100° Countersunk Head Screws, Short Thread, Shank Tolerance r6
47 十字槽100°沉头螺钉 [军标]
GJB 3372 (/45~/48) - 1998		 十字槽100°沉头螺钉
Cross Recessed 100° Countersunk Head Screws
48 十字槽100°小沉头螺钉 [军标]
GJB 3372 (/49~/52) - 1998		 十字槽100°小沉头螺钉
Cross recessed 100 ° small countersunk head screw
49 H型或Z型 十字槽沉头螺钉（普通头）产品等级A [印标]
IS 7485 (-1) - 2005		 H型或Z型 十字槽沉头螺钉（普通头）产品等级A
Countersunk flat head screws (common head style) with type H or Type Z cross recess - product grade A
50 十字槽沉头螺钉 [印标]
IS 7485 - 1985 (R2001)		 十字槽沉头螺钉
Cross recessed Countersunk head screws
51 90°米字槽沉头螺钉 [波兰标]
PN 82208		 90°米字槽沉头螺钉
90° Cross Recess Countersunk Flat Head Screws
52 82°十字槽沉头螺钉 (ASTM F837, F468) [美标]
ASME B 18.6.3 (H1B-I/H1B-IA) - 2024		 82°十字槽沉头螺钉 (ASTM F837, F468)
82° Cross Recessed Countersunk Head Screws (ASTM F837, F468)
供应商(2)
53 82°十字槽沉头螺钉 [Table 2] (ASTM F837, F468) [美标]
ASME B 18.6.3 (T2-I/T2-IA) - 2013		 82°十字槽沉头螺钉 [Table 2] (ASTM F837, F468)
82° Cross Recessed Countersunk Head Screws [Table 2] (ASTM F837, F468)
供应商(2)
54 100°十字槽沉头螺钉 (ASTM F837, F468) [美标]
ASME B 18.6.3 (H1D-I/H1D-IA) - 2024		 100°十字槽沉头螺钉 (ASTM F837, F468)
100° Cross Recessed Countersunk Head Screws (ASTM F837, F468)
55 100°十字槽沉头精整螺钉 [美标]
ASME B 18.6.3 (H1F-I/H1F-IA) - 2024		 100°十字槽沉头精整螺钉
Close Tolerance 100-deg Flat Countersunk Head Screws
56 十字槽82°沉头清根机械螺钉 [美标]
ASME B 18.6.3 (H3B-I/H3B-IA) - 2024		 十字槽82°沉头清根机械螺钉
Undercut 82-deg Flat Countersunk Head Screws，Type I and IA
57 82°小沉头十字槽螺钉 (ASTM F837 / F468) [美标]
ASME B 18.6.3 (H4A) - 2024		 82°小沉头十字槽螺钉 (ASTM F837 / F468)
82° Flat Coutersunk Trim head Screws (ASTM F837 / F468)
58 82°小沉头十字槽螺钉 [Table 13] (ASTM F837 / F468) [美标]
ASME B 18.6.3 (T13) - 2013		 82°小沉头十字槽螺钉 [Table 13] (ASTM F837 / F468)
82° Flat Coutersunk Trim head Screws [Table 13] (ASTM F837 / F468)
59 100°十字槽沉头螺钉 [Table 4] (ASTM F837, F468) [美标]
ASME B 18.6.3 (T4-I/T4-IA) - 2013		 100°十字槽沉头螺钉 [Table 4] (ASTM F837, F468)
100° Cross Recessed Countersunk Head Screws [Table 4] (ASTM F837, F468)
60 100°十字槽沉头精整螺钉 [美标]
ASME B 18.6.3 (T6-I/T6-IA) - 2013		 100°十字槽沉头精整螺钉
Close Tolerance 100-deg Flat Countersunk Head Screws (Machine Screws Only)
61 十字槽82°沉头清根机械螺钉 [美标]
ASME B 18.6.3 (T10-I/T10-IA) - 2013		 十字槽82°沉头清根机械螺钉
Undercut 82-deg Flat Countersunk Head Screws，Type I and IA
62 钛合金十字槽沉头螺钉 [航天]
QJ 2584 (A) - 2011		 钛合金十字槽沉头螺钉
Countersunk Head Screws With Cross Recess in Titanium Alloys
63 钛合金十字槽沉头螺钉 [航天]
QJ 2584 - 1993		 钛合金十字槽沉头螺钉
Countersunk Head Screws With Cross Recess in Titanium Alloys
64 十字槽沉头螺钉 [航天]
QJ 2377 - 1992		 十字槽沉头螺钉
Cross recessed countersunk head screws
65 十字槽120°沉头螺钉 [航空]
HB 1- 208 - 1995		 十字槽120°沉头螺钉
Cross Recess 120° Countersunk Head Screw
供应商(1)
66 十字槽90°沉头螺钉 [航空]
HB 1-206 - 2002		 十字槽90°沉头螺钉
90° Countersunk Head Screw with Cross Recess
67 钛合金光杆公差带f9高扭矩十字槽100°沉头螺栓 [航空]
HB 6565 - 1992		 钛合金光杆公差带f9高扭矩十字槽100°沉头螺栓
Titanium alloy smooth rod tolerance zone f9 high torque cross groove 100° countersunk head bolt
68 十字槽沉头机器螺钉 [深圳紧固件行业协会标准]
T/SZJGJ 001 (E) - 2024		 十字槽沉头机器螺钉
Cross Recessed Countersunk Head Screws
© 易紧通 服务热线：4006-164580（免长途费）