会员中心 | English | 繁體中文

开槽圆柱头螺钉 GB /T 65 - 2016

选择规格尺寸点击↓

M1.6

M2.5

(M3.5)

M10

括号内尺寸为非优选

尺寸单位: mm

模型下载

扫一扫分享

单重计算公差公制螺纹极限尺寸米/英制螺纹对照螺纹直径与受力截面积最小破坏扭矩牌号等级毛坯直径

千件重及价格计算千件重 : kg x 元/kg = 元/千件

默认密度 g/cm³

螺纹规格
d

M1.6

M2.5

(M3.5)

M10

P	螺距
a	最大值
d_k	最大值=公称
d_k	最小值
k	最大值=公称
k	最小值
n	公称
	最大值
	最小值
t	最小值
x	最大值
r	最小值

0.35	0.4	0.45	0.5	0.6	0.7	0.8	1	1.25	1.5
0.7	0.8	0.9	1.0	1.2	1.4	1.6	2.0	2.5	3.0
3	3.8	4.5	5.5	6	7	8.5	10	13	16
2.86	3.62	4.32	5.32	5.82	6.78	8.28	9.78	12.73	15.73
1.1	1.4	1.8	2	2.4	2.6	3.3	3.9	5	6
0.96	1.26	1.66	1.86	2.26	2.46	3.12	3.6	4.7	5.7
0.4	0.5	0.6	0.8	1	1.2	1.2	1.6	2	2.5
0.6	0.7	0.8	1	1.2	1.51	1.51	1.91	2.31	2.81
0.46	0.56	0.66	0.86	1.06	1.26	1.26	1.66	2.06	2.56
0.45	0.6	0.7	0.85	1	1.1	1.3	1.6	2	2.4
0.9	1.0	1.1	1.25	1.5	1.75	2.0	2.5	3.2	3.8
0.1	0.1	0.1	0.1	0.1	0.2	0.2	0.25	0.4	0.4

千件钢制重≈kg

螺纹长度b

最小值

①,尽可能不采用括号内的规格
②,公称长度＜35~45mm的螺钉，制出全螺纹（b=L-a）

替代列表

GB 65 - 1985 GB /T 65 - 2000 GB /T 65 - 2016

等效标准

国标 GB	国际 ISO	德标 DIN	意大利 UNI	法国 NF
GB /T 65	ISO 1207	DIN EN ISO 1207	UNI 6107	NF E 25-127

以上有部分标准可能为近似等效，如有异议以标准原件为准

采用标准

ISO 1207 - 2011

开槽圆柱头螺钉-产品等级A级

工艺相关

GB /T 152.3 - 1988

圆柱头用沉孔

GB /T 90.1

紧固件验收检查（ISO 3269:2000 IDT）

GB /T 90.2

紧固件标志与包装

GB /T 193

普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)

紧固件螺栓、螺钉、螺柱及螺母尺寸代号和标注

GB /T 5779.1

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 一般要求

紧固件机械性能有色金属制造的螺栓、螺钉、螺柱和螺母

模具相关

JB /T 4211.1 - 2014

螺钉冷镦模-终镦冲头 A型 (适用于GB65)

JB /T 4211.2 - 2014

螺钉冷镦模-凹模 A型 (适用于GB65、GB67、GB818)

JB /T 4211.2 - 2014

螺钉冷镦模-凹模 C型 (适用于GB65、GB67、GB818)

技术条件和引用标准

材料

钢

不锈钢

有色金属

通用技术条件
螺纹	公差
	标准
机械性能	等级
	标准
公差	产品等级
	标准
表面缺陷
表面处理	-
	-
验收及包装

GB/T 16938
6 g
GB/T 193、GB/T 9145
d＜3mm: 按协议； d≥3mm: 4.8、5.8	A2-50、A2-70	d＜3mm: 按协议； d≥3mm: CU2、CU3、AL4
d＜3mm: 按协议； d≥3mm: GB/T 3098.1	GB/T 3098.6	d＜3mm: 按协议； d≥3mm: GB/T 3098.10
A
GB/T 3103.1
GB/T 5779.1	-	-
不经处理；电镀技术要求按GB/T 5267.1; 非电解锌片涂层技术要求按 GB/T 5267.2	简单处理；钝化处理技术要求按 GB/T 5267.4	简单处理；电镀技术要求按 GB/T 5267.1
如需其他技术要求或表面处理，应由供需协议
GB/T 90.1 、GB/T 90.2

引用参考

GB /T 1172 - 1999

黑色金属硬度及强度换算值

GB /T 5267.1 - 2002

镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能

GB /T 193 - 2003

普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)

GB /T 3106 - 2016

紧固件 - 螺栓、螺钉和螺柱 - 公称长度和螺纹长度 (ISO 888:2012, MOD)

GB /T 3 - 1997

普通螺纹收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983)

GB /T 5779.1 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 一般要求

GB /T 5779.3 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 特殊要求

注：技术数据仅供参考，请以官方原件为准！

告诉我在“易紧通”看到，将给您优惠

浙江中域紧固件有限公司

联系人：李经理

1987721927 移动电话： 13968797079 电话：0577-62860077 微信号：13968797079 Email:

登陆后可见

材质：碳钢、不锈钢201、 304 、316；规格范围：M2-M20；公称长度：4-300mm；表面处理：镀锌、彩锌、镍、达克罗、黑锌。耐落抛光等。

[询价]

上海亚螺精密紧固技术有限公司

联系人：徐海

513543434 移动电话： 18621311857 电话：021-59766477 Email:

登陆后可见

材质：301、302、303、304、304L、316、316L、316Ti、317L、310S、321、347、1.4529、1.4539、1.4462、1.4547、1.4980、904L、2205、2507、2520、S32750、S32760、1Cr13、1Cr17、2Cr13、3Cr13、14Cr17Ni2、410、416、420、430、431、440、630、631、17-4PH、MP350N、600、601、625、660、718、750、800、825、925、926、C22、C276、A286、GH2132、GH4033、GH4080、GH4169、GH4145、9C18Mo、4Cr10Si2Mo、35CrMoA、42CrMoA、40CrNiMoA、25Cr2Mo1VA、SCM435、SCM440、4130、4140、4145、A36、A307、A320、A325、A490、A574、F1554，不锈钢、合金钢、钛合金、镍基合金、高温合金、耐蚀合金、镍钴合金、特种合金等；等级：A1-50、A2-50、A2-70、A2-80、A3-70、A4-70、A4-80、A4-90、A4-100、A5-80、B8、B8M、B8C、B8T、B6、B7、B7M、B16、C1-50、C1-70、C1-110、C3-80、C3-120、C4-70、D2-80、D2-100、D4-80、D4-100、D6-80、D6-100、D8-80、D8-100、P1-90、P1-120、F51、F53、F55、F60、10.9、12.9、14.9、15.9、16.9等；规格范围：M3-M120,1/4"-4"；表面处理：钝化、发黑、磷化、电泳、镀锌、镀镍、镀铬、镀镉、镀金、镀银、镀锡、镀铜、渗锌、海洋锌、渗铝、喷涂铝、达克罗、久美特、特氟龙、锌镍合金、镍钴合金、热镀锌、复合陶瓷、二硫化钼、二硫化钨、纳米涂层等，均可定制。

[询价]

苏州市桂丰精密不锈钢紧固件厂

联系人：杨钦移动电话： 15162465399 电话：0512-65808790 Email:

登陆后可见

材料：碳钢、不锈钢，表面处理：本色; 公称直径：M1.2-M8,公称长度：3mm-80mm

[询价]

江苏博凡科精密五金科技有限公司

联系人：汤继勇移动电话： 15298892886/15262400870 电话：0516-86839568 Email:

登陆后可见

材质：不锈钢、碳钢；公称直径范围：M1-M14；公称长度范围：5-400mm

[询价]

瑞安市精工组合紧固件厂

联系人：韩经理移动电话： 13616600328 电话：0577-65278085 Email:

登陆后可见

碳钢、不锈钢、铜；规格：M2.5-M10

[询价]

告诉我在“易紧通”看到，将给您优惠

类似标准及供货信息

1	[国标] GB /T 65 - 2000	开槽圆柱头螺钉 Slotted cheese head screws 供应商(5)
2	[国标] GB 65 - 1985	开槽圆柱头螺钉 Slotted Cheese Head Screws 供应商(5)
3	[国标] GB /T 2268 - 1991	机床夹具零件及部件钻套螺钉 The Parts And Units Of Jigs And Fixtures.drill Sleeve Screw
4	[国标] GB /T 2269 - 1991	机床夹具零件及部件镗套螺钉 The Parts And Units Of Jigs And Fixtures.boring Sleeve Screw
5	[国标] GB 830 - 1988	开槽圆柱头轴位螺钉 Slotted Cheese Head Screws With Shoulder
6	[国标] GB /T 832 - 1988	开槽带孔球面圆柱头螺钉 Slotted cap stan screws
7	[国标] GB /T 833 - 1988	开槽大圆柱头螺钉 Slotted large cheese head screws
8	[国标] GB /T 946 - 1988	开槽球面圆柱头轴位螺钉 Slotted Raised Cheese Head Screws with Shoulder
9	[国标] GB 66 - 1976	开槽球面圆柱头螺钉 Slotted Fillister Head Machine Screws
10	[德标] DIN 921 - 2014	开槽大盘头螺钉 Slotted Pan Head Screws With Large Head 供应商(2)
11	[德标] DIN 921 - 2007	开槽大盘头螺钉 Slotted pan head screws with large head 供应商(2)
12	[德标] DIN 7964 (A) - 1990	粗牙不脱出螺栓和螺钉 - 开槽矮圆柱头 Reduced shanke bolts and screws with coarse thread - Slotted cheese head 供应商(4)
13	[德标] DIN 84 - 1990	开槽圆柱头螺钉 Slotted Cheese Head Screws—Product Grade A 供应商(4)
14	[德标] DIN 921 - 1986	开槽大盘头螺钉 Slotted pan head screws with large head 供应商(2)
15	[德标] DIN 84 - 1970	开槽圆柱头螺钉 Slotted Cheese Head Screws 供应商(4)
16	[德标] DIN 404 - 2017	开槽带孔球面圆柱头螺钉 Slotted Capstan Screws
17	[德标] DIN 920 - 2012	开槽小盘头螺钉 Slotted Pan Head Screws With Small Head
18	[德标] DIN 923 - 2012	开槽盘头台阶螺钉 Slotted Pan Head Screws With Shoulder
19	[德标] DIN 404 - 2006	十字孔螺钉 Slotted Capstan Screws
20	[德标] DIN 920 - 2006	开槽小盘头螺钉 Slotted Pan Head Screws With Small Head
21	[德标] DIN 923 - 2006	开槽盘头台阶螺钉 Slotted pan head screws with shoulder
22	[德标] DIN 404 - 1986	开槽带孔球面圆柱头螺钉 Slotted Capstan Screws
23	[德标] DIN 920 - 1986	开槽小盘头螺钉 Slotted pan head screws with small head
24	[德标] DIN 923 - 1986	开槽盘头台阶螺钉 Slotted pan head screws with shoulder
25	[德标] DIN 43854 - 1979	电表用铅封螺栓 Sealing Bolts For Watthour Meters
26	[德标] DIN 8243 - 1969	机械用开槽圆柱头螺钉 Slotted cheese head screws for fine mechanics
27	[国际] ISO 1207 - 2011	开槽圆柱头螺钉-产品等级A级 Slotted Cheese Head Screws - Product Grade A 供应商(1)
28	[国际] ISO 1207 - 1992	开槽圆柱头螺钉 A级 Slotted Cheese Head Screws - Product Grade A 供应商(1)
29	[日标] JIS B 1101 (T3) - 2017	开槽矮圆柱头螺钉 [表3] Slotted Cheese Head Screws [Table 3] 供应商(1)
30	[日标] JIS B 1101 (AT1) - 1996	开槽矮圆柱头螺钉表1 [Attached Table 1] Slotted Cheese Head Screws [Attached Table 1] 供应商(1)
31	[日标] JIS B 1101 (JA10) - 2017	开槽圆柱头螺钉附表JA.10 Slotted Fillister Head Screws - Table JA.10
32	[日标] JIS B 1101 (JA9) - 2017	开槽圆柱头螺钉附表JA.9 Slotted Flat Fillister Head Screws - Table JA.9
33	[日标] JIS B 1101 (JA7) - 2017	开槽扁圆柱头螺钉附表JA.7 Slotted Binding Head Screws - Table JA.7
34	[日标] JIS B 1116 - 2009	精密机械用开槽圆柱头螺钉 Slotted Cheese Head Screws For Fine Mechanics
35	[日标] JIS B 1101 (AAT8) - 1996	开槽矮圆柱头螺钉附表8 [Annex Attached Table 8] Slotted Fillister Head Screws [Annex Attached Table 8]
36	[日标] JIS B 1101 (AAT7) - 1996	开槽圆柱头螺钉附表7 [Annex Attached Table 7] Slotted Flat Fillister Head Screws - Annex Attached Table 7
37	[日标] JIS B 1101 (AAT5) - 1996	开槽扁圆柱头螺钉附表5【Annex Attached Table 5】 Slotted Binding Head Screws 【Annex Attached Table 5】
38	[日标] JIS B 1119 (1CF) - 1986	眼镜框架用 - 开槽平头倒角螺钉 Spectacle Frames - Slotted Chamfered Flat Head Screws
39	[日标] JIS B 1119 (1RF) - 1986	眼镜框架用 - 开槽弧面平头螺钉 Spectacle Frames - Slotted Round Flat head screws
40	[日标] JIS B 1119 (1F) - 1986	眼镜框架用 - 开槽平头螺钉 Spectacle Frames - Slotted Flat Machine Screws
41	[机械行业] JB /T 8045.5 - 1999	钻套螺钉 Drill Sleeve Screw
42	[机械行业] JB /T 8046.3 - 1999	镗套螺钉 Boring Sleeve Screw
43	[美标] ASME/ANSI B 18.6.3 (T21) - 2010	开槽球面圆柱头螺钉Table21 Slotted Fillister Head Machine Screws
44	[美标] ASME/ANSI B 18.6.3 - 2010	开槽球面圆柱头头部带孔螺钉Table23 Slotted drilled fillister head screws (machine screws only)
45	[美标] ASME/ANSI B 18.6.3 - 2010	开槽球面圆柱头螺钉Table27 Slotted binding head screws (machine screws only)
46	[美标] ASME/ANSI B 18.6.2 (T3) - 1998 (R2010)	开槽球面圆柱头螺钉 [Table 3] (A307, SAE J429, F468, F593) Slotted [Table 3] (A307, SAE J429, F468, F593)
47	[美标] ASME/ANSI B 18.11 - 1961 (R1983)	开槽圆柱头/球面圆柱头小螺钉 [Table 1] Slotted fillister head miniature screws
48	[意大利] UNI 6422 - 1969	开槽圆柱头螺钉 Slotted cheese head screws for manufacture of railway and tramway rolling stock - ISO metric coarse
49	[意大利] UNI 6107 - 1967	开槽圆柱头螺钉 Slotted Cheese Head Screws-ISO Metric Coarse Thread - Product Grade A
50	[法国] NF E 25-127 - 1994	开槽圆柱头螺钉 Slotted Cheese Head Screws - Product Grade A
51	[法国] NF F 03-005 (C) - 1983	铁路车辆圆柱头侧切口机械螺钉 Railway rolling stock Grade A Notched cheese head machine screws
52	[英标] BS 1981 - 1991	开槽球面圆柱头螺钉Table14 Slotted Raised Cheese Head Screws
53	[英标] BS 4183 (T5) - 1967	开槽圆柱头机械螺钉 Slotted cheese head machine screws. Metric series
54	[英标] BS 450 - 1958	英制开槽圆柱头螺钉 - B.S.W. & B.S.F. 螺纹 [Table 6] Slotted Cheese Head Screws with B.S.W. & B.S.F. Threads [Table 6]
55	[澳标] AS /NZS 1427 - 1996	米制开槽圆柱头螺钉 [Table 4] ISO metric slotted cheese head screws [Table 4]
56	[台湾] CNS 9668 - 1988	开槽扁圆顶柱头小螺钉 Slotted (Oval) Fillister Head Machine Screws
57	[台湾] CNS 9670 - 1988	开槽圆柱头螺钉 Slotted Cheese Head Screws
58	[台湾] CNS 9673 - 1988	开槽扁圆顶锥头小螺钉 Slotted Mushroom Head Screws With Cone Point
59	[台湾] CNS 9680 - 1982	精密机械用开槽圆柱头螺钉 Slotted Cheese Head Screws For Fine Mechanics
60	[台湾] CNS 4413 - 1981	电开关用开槽圆柱沉头螺钉 Slotted Cheese Head Screws For Electric Switch
61	[台湾] CNS 4251 - 1980	开槽带孔圆柱头螺钉 Slotted Cheese Head Screw Head Hole
62	[台湾] CNS 4355 - 1980	开槽圆柱头螺钉 Slotted Cheese Head Screws
63	[台湾] CNS 4356 - 1980	开槽大圆柱头螺钉 Slotted Large Cheese Head Screws
64	[台湾] CNS 4358 - 1980	开槽圆柱头轴位螺钉 Slotted Cheese Head Screws With Shoulder
65	[台湾] CNS 4360 - 1980	开槽小圆柱头螺钉 Slotted Cheese Head Screw With Small Head
66	[台湾] CNS 4362 - 1980	精密用开槽圆柱头螺钉 Slotted Cheese Head Screws For Fine Mechanics
67	[韩标] KS B 1021 (T3) - 2012 (R2022)	开槽圆柱头螺钉【Table 3】 Slotted Cheese Head Screws 【Table 3】
68	[韩标] KS B 1021 - 1998	开槽圆柱头螺钉 Slotted Cheese Head Screws
69	[企标] YJT 4011	塑料开槽圆柱头滚花螺钉 Plastic slotted cheese head knurl screws
70	[企标] YJT 4017	塑料开槽大圆柱头台阶螺钉 Plastic slotted large cheese head screws with shoulder
71	[企标] YJT 4018	塑料一字槽圆柱头带垫螺钉 Plastic Slot(-) cheese head screws with collar
72	[德标] DIN EN ISO 1207 - 2011	开槽圆柱头螺钉-产品等级A级 Slotted Cheese Head Screws—Product Grade A 供应商(4)
73	[德标] DIN EN ISO 1207 - 1994	开槽圆柱头螺钉-产品等级A级 Slotted Cheese Head Screws—Product Grade A 供应商(4)
74	[军标] GJB 3371 (/33~/39) - 1998	圆柱头螺栓 Cheese Head Bolts
75	[军标] GJB 3371 (/40~/44) - 1998	头部带保险孔的圆柱头螺栓 Cheese Head Bolts With Wire Holes On Head
76	[军标] GJB 3372 (/11~/17) - 1998	圆柱头螺钉开槽 Cheese Head Screws, Slotted
77	[军标] GJB 3372 (/18~/24) - 1998	头部带保险孔的圆柱头螺钉 Cheese Head Screws With Wire Holes On Head
78	[军标] GJB 3372 (/54~/55) - 1998	头部带保险孔的不脱出圆柱头螺钉 Cheese Head Screws With Wire Holes On Head, Waisted Shank
79	[军标] GJB 3372 (/57~/59) - 1998	固定表盘螺钉 Slotted Fillister Head Machine Screws
80	[印标] IS 1366 - 2002	开槽圆柱头螺钉 A级 Slotted Cheese Head Screws - Product Grade A
81	[美标] ANSI B 18.11 - 1961 (R2017)	开槽圆柱头/球面圆柱头小螺钉 [Table 1] (A276, B16, B151) Slotted fillister head miniature screws [Table 1] (A276, B16, B151)
82	[美标] ANSI B 18.11 - 1961 (R2017)	开槽联头（扁圆柱头）小螺钉 [Table 4] (A276, B16, B151) Slotted Binding Head Miniature Screws [Table 4] (A276, B16, B151)
83	[美标] ASME B 18.6.3 (H6A) - 2024	开槽球面圆柱头螺钉 (ASTM F837, F468) Slotted Fillister Head Screws (ASTM F837, F468)
84	[美标] ASME B 18.6.3 (H6C) - 2024	球面圆柱头,头部带孔螺钉 (ASTM F837, F468) Slotted Drilled Fillister Head Screws (Machine Screws Only) (ASTM F837, F468)
85	[美标] ASME B 18.6.3 (H8A) - 2024	开槽球面扁圆柱头机械螺钉 (ASTM F837, F468) Slotted Binding Head Screws (ASTM F837, F468)
86	[美标] ASME B 18.6.3 (T21) - 2013	开槽球面圆柱头螺钉 [Table 21] (ASTM F837, F468) Slotted Fillist Head Screws [Table 21] (ASTM F837, F468)
87	[美标] ASME B 18.6.3 (T23) - 2013	球面圆柱头,头部带孔螺钉 [Table 23] (ASTM F837, F468) Slotted Drilled Fillister Head Screws (Machine Screws Only) [Table 23] (ASTM F837, F468)
88	[美标] ASME B 18.6.3 (T27) - 2013	开槽球面扁圆柱头机械螺钉[Table 27] (ASTM F837, F468) Dimensions of Slotted Binding Head Screws (Machine Screws Only) (ASTM F837, F468)
89	[航天] QJ 2368 - 1992	开槽带孔圆柱头螺钉 Slotted cheese head screws with holes
90	[航天] QJ 2371 - 1992	开槽圆柱头螺钉 Slotted cheese head screws
91	[航天] QJ 2382 - 1992	开槽球面圆柱头轴位螺钉 Slotted raised cheese head screws with shoulder
92	[航天] QJ 2383 - 1992	开槽球面大圆柱头螺钉 Slotted large raised cheese head screws
93	[航天] QJ 2385 - 1992	开槽带孔圆柱头螺钉 Slotted cheese head screws with holes
94	[航空] HB 1- 127 - 2002	头部带保险孔的圆柱头螺栓 Cheese head bolts with wire holes on head
95	[航空] HB 1- 203 - 2002	头部带保险孔的圆柱头螺钉 Cheese Head Screws With Wire Holes On Head
96	[航空] HB 1- 202 - 1995	圆柱头螺钉 Slotted Cheese Head Screws