会员中心 | English | 繁體中文

滚花高头台阶螺钉 DIN 464 - 1986

选择规格尺寸点击↓

M1.2

M1.4

M1.6

M2.5

(M3.5)

M10

括号内尺寸为非优选

尺寸单位: mm

模型下载替

扫一扫分享

公差公制螺纹极限尺寸米/英制螺纹对照螺纹直径与受力截面积最小破坏扭矩牌号等级毛坯直径

千件重及价格计算千件重 : kg x 元/kg = 元/千件

默认密度 g/cm³

螺纹尺寸
d

M1.2

M1.4

M1.6

M2.5

(M3.5)

M10

P
b	最大值
	最小值
d_k	公称
	最大值
	最小值
d_s	最大值=公称
	最小值
h	公称
	最大值
	最小值
k	最大值=公称
	最小值
n	最大值
	公称
	最小值
t	最小值
	最大值
c
r
x	最大值

0.25	0.25	0.3	0.35	0.4	0.45	0.5	0.6	0.7	0.8	1	1.25	1.5
3.5	4	4.6	5.7	6.8	8.9	10	11.2	13.4	16.6	20	26.5	33
3	3.5	4	5	6	8	9	10	12	15	18	24	30
5.50	6	7	7.5	9	11	12	14	16	20	24	30	36
5.74	6.24	7.29	7.79	9.29	11.35	12.35	14.35	16.35	20.42	24.42	30.42	36.5
5.26	5.76	6.71	7.21	8.71	10.65	11.65	13.65	15.65	19.58	23.58	29.58	35.5
2.80	3	3.5	3.8	4.5	5	6	7	8	10	12	16	20
2.55	2.75	3.2	3.5	4.2	4.7	5.7	6.64	7.64	9.64	11.57	15.57	19.48
3.50	4	4.7	5	5.3	6.5	7.5	8.5	9.5	11.5	15	18	23
3.74	4.24	4.94	5.24	5.54	6.79	7.79	8.79	9.79	11.85	15.35	18.35	23.42
3.26	3.76	4.46	4.76	5.06	6.21	7.21	8.21	9.21	11.15	14.65	17.65	22.58
1.50	1.5	2	2	2	2.5	2.5	3	3.5	4	5	6	8
1.25	1.25	1.75	1.75	1.75	2.25	2.25	2.75	3.2	3.7	4.7	5.7	7.64
0.30	0.4	0.4	0.4	0.5	0.6	0.8	0.8	1	1.2	1.6	2	2.5
0.36	0.46	0.46	0.46	0.56	0.66	0.86	0.86	1.06	1.26	1.66	2.06	2.56
0.50	0.6	0.6	0.6	0.7	0.8	1	1	1.2	1.51	1.91	2.31	2.81
0.70	0.8	0.9	1	1.1	1.5	1.8	2	2.2	2.8	3.5	4.5	6
0.90	1	1.15	1.3	1.4	1.8	2.2	2.5	2.7	3.4	4.3	5.5	7
①	①	①	①	①	0.3	0.3	0.3	0.3	0.3	0.5	0.6	0.8
0.5	0.5	0.5	0.5	0.5	0.5	0.5	0.5	0.5	1	1	2	2
0.75	0.75	0.9	1.05	1.2	1.35	1.5	1.8	2.1	2.4	3	3.75	4.5

千件钢制重≈kg

①,边缘倒角

替代列表

DIN 464 - 1986 DIN 464 - 2007

技术条件和引用标准

材料

钢

不锈钢

有色金属

通用要求
螺纹	公差
	标准
机械性能 ^④	等级
	标准
公差	产品等级
	标准
表面处理 ^⑤	-
	-
验收及包装
备注

DIN 267 part 1
≤ M1.4：6h ≥ M1.6：6g^①
DIN 13 part 15
钢St^②	A1-50，C4-50	CuZn = 铜锌合金^③
DIN 1651^②	DIN 267 part 11	DIN 267 part 18
≤ M1.4：F ≥ M1.6：A
DIN 267 part 6，ISO 4759 part 1
不经处理	blank	blank
电镀 DIN 267 Part 9 DIN 267 Part 19 shall apply with regard to permissible surtace discontinuities. DIN 50942 shall apply with regard to phosphating of metals.
DIN 267 part 5^⑥
① Applies only for screws without surface protection. 6g makes it possible for normal coating thicknesses to be applied in accordance with DIN 267 Part 9 with the reference line (h position) not being exceeded. The coating thickness may require a fundamental deviation larger than that specified for the g position, which however may impair the resistance to stripping of the bolt / nut assembly. ② St = 9 SMnPb 28 K as specified in DIN 1651 or an equivalent steel in terms of strength, This material shall also be used in cases where property class 5.8 is given in existing documentation. ③ CuZn = CU2 or CU3 (as specified in DIN 267 Part 18). at the manufacturer's discretion. ④ Other property classes or materials shall be subject to agreement. ⑤ R^z 25 or R^z 16 shall apply for the surface roughness, as appropriate. R^z 16 for thread flanks of sizes not exceeding M5, R^z 40 for thread flanks in the case of machine cut threads exceeding size M5 and R^z 100 for thread ends. ⑥ AQL (acceptable quality level) 1 shall appy for major characteristics and AQL1.5 for minor characteristics, thread size d and the straight knurl being regarded as major characteristics, lengths L and h, collar diameter, ds, and external diameter, dk, as minor characteristics.

引用参考

GB /T 1172 - 1999

黑色金属硬度及强度换算值

GB /T 5267.1 - 2002

镀锌、镀镍、镀镉、复合镀等层镀层盐雾腐蚀的防护性能

GB /T 193 - 2003

普通螺纹（一般用途米制螺纹）- 直径与螺距系列 (ISO 261: 1998, MOD)

GB /T 3106 - 2016

紧固件 - 螺栓、螺钉和螺柱 - 公称长度和螺纹长度 (ISO 888:2012, MOD)

GB /T 3 - 1997

普通螺纹收尾、肩距、退刀槽和倒角 (ISO 3508:1976 / ISO 4755:1983)

GB /T 5779.1 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 一般要求

GB /T 5779.3 - 2000

紧固件表面缺陷 - 螺栓、螺钉和螺柱 - 特殊要求

注：技术数据仅供参考，请以官方原件为准！

告诉我在“易紧通”看到，将给您优惠

深圳煜之峰五金制品有限公司

联系人：庄宏伟移动电话： 13008864675 电话：0755-89505088 Email:

登陆后可见

材质：碳钢、合金钢、不锈钢、铜、铝、钛；规格范围：M0.6~M6；公称长度：1~50mm；表面处理：镀锌、镍、锌镍合金、电泳、达克罗、CD纹、PVD等。

[询价]

余姚市鸿特盛金属制品有限公司

联系人：马华珍/徐天阳移动电话： 13095941973, 18268663653 电话：0574-62761228 Email:

登陆后可见

材料：不锈钢A2-70，A2-80，A4-70，A4-80，A2（302,303,304），A4(316)，410，430 公称范围：规格齐全

[询价]

类似标准及供货信息

1	[国标] GB 834 - 1988	滚花高头螺钉 Knurled Thumb Screws 供应商(2)
2	[国标] GB 835 - 1988	滚花平头螺钉 Knurled Screws 供应商(2)
3	[国标] GB /T 836 - 1988	滚花小头螺钉 Knurled Screws with Small Head 供应商(1)
4	[国标] GB 839 - 1988	滚花头不脱出螺钉 Knurled Thumb Screws with Waisted Shank 供应商(1)
5	[国标] GB /T 2163 - 1991	机床夹具零件及部件活动手柄压紧螺钉 The Parts And Units Of Jigs And Fixtures.movable Handle Holddown Screw
6	[国标] GB /T 840 - 1988	塑料滚花头螺钉 Plastic diamond knurlhead screws
7	[德标] DIN 464 - 2006	滚花高头台阶螺钉 Knurled Thumb Screws, High Type 供应商(2)
8	[德标] DIN 653 - 2006	薄型滚花手拧螺钉 Knurled Thumb Screws, Low Type 供应商(1)
9	[德标] DIN 7964 (F) - 1990	粗牙不脱出螺栓和螺钉 - 滚花高头台阶螺钉 Reduced shanke bolts and screws with coarse thread - Knurled Thumb Screws, High Type 供应商(4)
10	[德标] DIN 653 - 1986	平头滚花螺钉, 薄型 Knurled Thumb Screws,thin Type 供应商(1)
11	[德标] DIN 465 - 1963	高型开槽滚花头螺钉 Slotted knurled screws-High style 供应商(1)
12	[德标] DIN 6367 - 2003	套式铣刀刀杆用铣刀紧固螺丝, 十字头螺钉（手拧螺钉） Cutter Retaining Screws For Milling Machine Arbors
13	[机械行业] JB /T 8026.3 - 1999	圆柱头调节支承 Adjustable Cylindor Head Supporters
14	[机械行业] JB /T 9162.14 - 1999	带孔滚花螺钉 Knurled Screws With Radial Holes
15	[机械行业] JB /T 9162.15 - 1999	压紧螺钉 Clamping Screw
16	[机械行业] JB /T 9162.16 - 1999	滚花圆柱头螺钉 Knurled Head Cap Screws
17	[法国] NF E 27-170 - 1974	滚花头台阶螺钉 Knurled Thurmb Screws
18	[台湾] CNS 4658 - 1984	T形旋柄螺钉 Rotary Handle Screws - T Type
19	[航天] QJ 2381 - 1992	滚花头不脱出螺钉 Knurled thumb screws with waisted shank
20	[航天] QJ 2384 - 1992	滚花高头螺钉 Knurled thumb screws